Cisco Catalyst 6816-X-LE Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 100

background image

• Positioned so approximately one half of the chassis protrudes in front of the rack:

• Remove the screws in the L brackets.

• Reposition the L brackets to align with the second set of holes behind the holes where the L brackets

were originally installed (see figure below).

• Secure the brackets with the screws.

Figure 19: Locations of Screw Holes for Alternate Chassis Installation Positions

Screw holes for
reattaching the L brackets.
When the chassis is
installed, approximately
one quarter of it protrudes
in front of the rack.

3

Left L bracket already
attached. When the
chassis is installed, the
front of the chassis is
approximately flush with
the front of the rack.

1

Screw holes for
reattaching the L brackets.
When the chassis is
installed, approximately
one half of it protrudes in
front of the rack.

4

Right L bracket already
attached. When the
chassis is installed, the
front of the chassis is
approximately flush with
the front of the rack.

2

Step 2

Rest the back end of the chassis on the rack-mount shelf and carefully slide the chassis into the rack until the
L brackets meet the front rails of the rack system.

Step 3

Locate the rack post holes that align with the chassis L bracket holes. If the rack post holes are prethreaded,
determine if the threads are 10-32 or 12-24. If the rack post holes are unthreaded, install eight or ten (four or
five on each side) either 10-32 or 12-24 clip or cage nuts over the rack post holes to accept the installation
screws.

Clip nuts or cage nuts are not included as part of the accessory kit that comes with the chassis. You
must obtain them yourself.

Note

Step 4

If you want to install one or both of the optional cable guide assemblies, position the cable guides so that the
cable guide mounting holes are aligned with L bracket holes as shown in figure below.

Catalyst 6840-X Switch Series Hardware Installation Guide

43

Installing the Switch

Installing the Chassis in a Two-Post Rack

«
...
53
54
55
56
57
...
»

Содержание Catalyst 6816-X-LE





































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 6816-X-LE

WJSX150 - SWITCHER - ADDENDUM

Бренд: Panasonic Страницы: 48

Бренд: Jabra Страницы: 4

LINK 14201-20 - DATASHEET FOR TOSHIBA PHONES

Бренд: Jabra Страницы: 2

Бренд: Abtus Страницы: 15

Бренд: Zektor Страницы: 65

Бренд: Hall Technologies Страницы: 35

LVP-51 LVP-51 Series

Бренд: Omega Engineering Страницы: 6

Бренд: N-Tron Страницы: 17

FL SWITCH SFN 16TX

Бренд: Phoenix Contact Страницы: 6

Бренд: Ruby Tech Страницы: 301

SmartSwitch SBU128

Бренд: Cabletron Systems Страницы: 76

Бренд: ALFAtron Страницы: 15

Бренд: Eaton Страницы: 3

Бренд: JUKI Страницы: 2

JetNet 5428G-20SFP Series

Бренд: Korenix Страницы: 2

Бренд: Datavideo Страницы: 90

Бренд: Stahl Страницы: 44

SL-5-DS-2 SWITCH AND CHECK VALVE

Бренд: BENDIX Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды