Cisco Catalyst 6816-X-LE Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 100

background image

Hazardous voltage or energy may be present on DC power terminals. Always replace cover when terminals
are not in service. Be sure uninsulated conductors are not accessible when cover is in place.

Statement 1075.

Warning

Procedure

Step 1

Turn off the power at the circuit breakers for the portions of the DC grid power that you are connecting to
and verify that all of the LEDs on the power supplies are off.

Step 2

Using a 1/8" flat head screwdriver or No. 1 Phillips head screwdriver, loosen the set screws on the connector
to freely accept the power wires. The connector will accept 8-24 AWG wires, use what your local electrical
code calls for.

Step 3

Strip 1/2" of insulation off the DC wires that you are using.

Step 4

Insert the black (DC negative) wire into the right aperture on the connector and tighten down the connection
set screw. Finger tight or about 3 ft./lbs should be sufficient.

Step 5

Insert the red (DC positive) wire into the left aperture on the connector and tighten down the connection set
screw. Do not tighten over 0.7 Nm.

Figure 28: Connecting to a DC Power Source

Step 6

For the powered down circuits connected to the power supplies, turn on the power at the circuit breaker. The
LEDs should flash and then the INPUT OK LED on the power supply should turn on.

Catalyst 6840-X Switch Series Hardware Installation Guide

58

Installing and Removing Power Supplies

Connecting to a DC Power Source

«
...
68
69
70
71
72
...
»

Содержание Catalyst 6816-X-LE





































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 6816-X-LE

Бренд: S&C Страницы: 26

Бренд: S&C Страницы: 37

Бренд: S&C Страницы: 28

Бренд: H3C Страницы: 17

Бренд: Zektor Страницы: 17

Бренд: rako Страницы: 4

Бренд: DAITEM Страницы: 37

Бренд: Zektor Страницы: 65

Бренд: TRENDnet Страницы: 11

Edison Cooper Power Series

Бренд: Eaton Страницы: 12

Бренд: 3Com Страницы: 62

Elinx EIR510-2MC-T

Бренд: B&B Electronics Страницы: 107

Бренд: ADC Страницы: 75

IES6200-PN-16T4GS-2P48

Бренд: 3onedata Страницы: 3

Бренд: Intermatic Страницы: 1

Бренд: SMC Networks Страницы: 1

Бренд: Copal Страницы: 9

Бренд: GarrettCom Страницы: 42

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды