Cisco Catalyst 6816-X-LE Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 100

background image

A P P E N D I X

B

Module Connectors and Cable Specifications

•

Module Connectors, on page 71

•

Cables and Adapters, on page 72

•

Cleaning the Fiber-Optic Connectors, on page 74

Module Connectors

RJ-45 Connector

The RJ-45 connector is used to connect a Category 3, Category 5, Category 5e, or Category 6 foil twisted-pair
or unshielded twisted-pair cable from the external network to the module interface connector.

Figure 32: RJ-45 Interface Cable Connector

Category 5e, Category 6, and Category 6a cables can store large levels of static electricity because of the
dielectric properties of the materials used in their construction. Always ground the cables (especially in new
cable runs) to a suitable and safe earth ground before connecting them to the module.

Caution

To comply with GR-1089 intrabuilding and lightning immunity requirements, you must use a foil twisted-pair
(FTP) cable that is properly grounded at both ends.

Caution

LC Connector

The LC fiber optic connector is a small form-factor fiber-optic connector that provides high-density fiber
connectivity. The LC connector can be used with either MMF cable or SMF cable. The LC connector uses a
latching clip mechanism that is similar to the one used on the RJ-45 copper connector.

Catalyst 6840-X Switch Series Hardware Installation Guide

71

«
...
81
82
83
84
85
...
»

Содержание Catalyst 6816-X-LE





































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 6816-X-LE

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 2

Бренд: NEC Страницы: 168

Бренд: A SYSTEMS Страницы: 16

Бренд: Panasonic Страницы: 20

Бренд: Panasonic Страницы: 281

Бренд: B&K Страницы: 28

Бренд: B&K Страницы: 2

INTEGRA KLI 310

Бренд: Velux Страницы: 9

Custom Pro Matrix

Бренд: Bluestream Страницы: 27

Бренд: Omron Страницы: 4

Бренд: IDT Страницы: 158

Бренд: Black Box Страницы: 3

Бренд: BERNSTEIN Страницы: 38

Бренд: serverLink Страницы: 2

Бренд: Metra Electronics Страницы: 8

Бренд: Lindy Страницы: 54

Бренд: Opengear Страницы: 109

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды