Cisco Catalyst 6816-X-LE Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 100

background image

Power Source Interruptions

Systems are especially sensitive to variations in voltage supplied by the AC power source. Overvoltage,
undervoltage, and transients (or spikes) can erase data from memory or even cause components to fail. To
protect against these types of problems, power cables should always be properly grounded. Also, place the
system on a dedicated power circuit (rather than sharing a circuit with other heavy electrical equipment). In
general, do not allow the system to share a circuit with any of the following:

• Copy machines

• Air conditioners

• Vacuum cleaners

• Space heaters

• Power tools

• Teletype machines

• Laser printers

• Facsimile machines

• Any other motorized equipment

Besides these appliances, the greatest threats to a system's power supply are surges or blackouts that are caused
by electrical storms. Whenever possible, turn off the system and peripherals, if any, and unplug them from
their power sources during thunderstorms. If a blackout occurs—even a temporary one—while the system is
turned on, turn off the system immediately and disconnect it from the electrical outlet. Leaving the system on
may cause problems when the power is restored; all other appliances left on in the area may create large
voltage spikes that may damage the system.

System Grounding

You must install a system ground as part of the chassis installation process. Chassis installations that rely only
on the AC third-prong ground are insufficient to adequately ground the systems.

Proper grounding practices ensure that the buildings and the installed equipment within them have
low-impedance connections and low-voltage differentials between chassis. When you install a system ground,
you reduce or prevent shock hazards, chances of equipment damage due to transients, and the potential for
data corruption.

Without proper and complete system grounding, you run the risk of increased component damage due to ESD.
Additionally, you have a greatly increased chance of data corruption, system lockup, and frequent system
reboot situations by not using a system ground.

Installations that rely solely on system grounding that uses only an AC third-prong ground run a substantially
greater risk of equipment problems and data corruption than those installations that use both the AC third-prong
ground and a properly installed system ground.

Caution

The following table lists some general grounding practice guidelines.

Catalyst 6840-X Switch Series Hardware Installation Guide

26

Preparing for Installation

Power Source Interruptions

«
...
36
37
38
39
40
...
»

Содержание Catalyst 6816-X-LE





































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 6816-X-LE

Бренд: D-Link Страницы: 267

Бренд: H3C Страницы: 1089

Бренд: Xantech Страницы: 2

AVS-OCT-6448-210

Бренд: AMX Страницы: 1

Бренд: Abseco Страницы: 10

VIGILANT VTS0400

Бренд: RONK Страницы: 32

Бренд: A-Neuvideo Страницы: 9

Бренд: UniFi Страницы: 13

TIMEGUARD IS3N-20

Бренд: Theben Страницы: 2

Бренд: Ascent Communication Technology Страницы: 8

ACTIVE with NETATMO

Бренд: Velux Страницы: 20

ECRAFT SMART HOME Series

Бренд: Globalmediapro Страницы: 4

Orion XC OXS-XC008-FS

Бренд: Rose electronics Страницы: 132

Бренд: SMC Networks Страницы: 13

Бренд: Larson Electronics Страницы: 4

Бренд: Linksys Страницы: 2

Бренд: SMART-AVI Страницы: 18

FD-M2-EX7 Series

Бренд: pizzato Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды