Cisco Catalyst 6816-X-LE Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 100

background image

Installing the Switch Chassis

Installation Accessory Kits

The switch chassis is designed to be installed in a standard 19-inch rack, either open or enclosed. The chassis
is shipped with the 19-inch rack-mount L brackets that are factory installed on the left-front and right-front
of the chassis. Screws are included with the accessory kit that are used to secure the chassis in the rack
enclosure.

Depending on the manufacturer, the rack posts might be prethreaded to accept either 10-32 or 12-24 screws.
If the rack posts are not prethreaded, you must install 10-32 or 12-24 clip nuts or cage nuts to secure the
rack-mount screws. The clip nuts or the cage nuts are not included as part of the accessory kit and must be
obtained on your own.

Note

The accessory kit also contains the following:

• Cable guides— Two cable guides can be installed on the front of the chassis using the same sets of screws

that secure the chassis rack-mount brackets to the rack posts.

L Brackets on the Chassis

The switch chassis is shipped with two L brackets installed toward the front of each side of the chassis, as
shown in the following figure.

Figure 14: Brackets on the Switch Chassis

Right L bracket

2

Left L bracket

1

Catalyst 6840-X Switch Series Hardware Installation Guide

39

Installing the Switch

Installing the Switch Chassis

«
...
49
50
51
52
53
...
»

Содержание Catalyst 6816-X-LE





































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 6816-X-LE

S5500-SI Series

Бренд: H3C Страницы: 130

S5500-EI series

Бренд: H3C Страницы: 19

S5500-EI series

Бренд: H3C Страницы: 91

S5500-EI series

Бренд: H3C Страницы: 24

S5500-EI series

Бренд: H3C Страницы: 69

S5120-SI Series

Бренд: H3C Страницы: 4

S5120-SI Series

Бренд: H3C Страницы: 209

S5120-SI Series

Бренд: H3C Страницы: 70

S5120-EI Series

Бренд: H3C Страницы: 32

Бренд: H3C Страницы: 83

Бренд: H3C Страницы: 26

S5500-SI Series

Бренд: H3C Страницы: 6

Бренд: Ruby Tech Страницы: 2

Бренд: Touch-plate Страницы: 12

Бренд: König Страницы: 8

Бренд: Mach Power Страницы: 12

Unified Gigabit Wireless PoE Switch 24...

Бренд: 3Com Страницы: 40

FlowPoint 2100 12

Бренд: Cabletron Systems Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды