Cisco Catalyst 6816-X-LE Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 100

background image

• If the OK LED then goes on, return the first power cord for replacement.

If this unit has more than one power cord, repeat Step 1 for each power supply.

If the OK LED still fails to light when the switch is connected to a different power source with a new power
cord, the power supply is probably faulty.

If a second power supply is available, install it in the second power supply bay, and contact a customer service
representative for further instructions.

Step 2

If you have a second power supply, repeat Step 1 for this power supply.

What to do next

If you are unable to resolve the problem or if you determine that either a power supply or backplane connector
is faulty, see

Contacting Cisco Customer Service, on page 82

Troubleshooting the Fan Tray

To isolate a fan tray problem, follow these steps:

Procedure

Step 1

Verify that the FAN LED on the fan tray is green.

If the FAN LED is not green, see

Contacting Cisco Customer Service, on page 82

to determine whether or

not the power subsystem is functioning properly.

Step 2

Check to determine if the FAN LED is amber. If the FAN LED is amber, the fan tray is not seated in the
backplane or has malfunctioned.

Do the following:

• To ensure that the fan tray is seated properly, loosen the captive installation screws, remove the fan tray,

and reinstall it.

• Tighten all captive installation screws, and then restart the system.

• If the FAN LED is still amber, the system detects an individual fan failure. Contact a customer service

representative for instructions.

Catalyst 6840-X Switch Series Hardware Installation Guide

81

Troubleshooting

Troubleshooting the Fan Tray

«
...
91
92
93
94
95
...
»

Содержание Catalyst 6816-X-LE





































































































Отзывы:

Нет отзывов

Похожие инструкции для Catalyst 6816-X-LE

Бренд: Nectarine Health Страницы: 9

Бренд: Lantronix Страницы: 40

Бренд: Lantronix Страницы: 2

SISTP1040-551-LRT

Бренд: Lantronix Страницы: 2

Бренд: Lantronix Страницы: 2

SISPM1040-3 L Series

Бренд: Lantronix Страницы: 2

SISPM1040 L3 Series

Бренд: Lantronix Страницы: 36

SecureLinx Spider

Бренд: Lantronix Страницы: 18

Бренд: Lantronix Страницы: 8

Бренд: Lantronix Страницы: 6

SISPM1040-582-LRT

Бренд: Lantronix Страницы: 272

Xpress-Pro SW 52000

Бренд: Lantronix Страницы: 8

MMAC-Plus 9H423-26

Бренд: Cabletron Systems Страницы: 14

Gigabit Switch 8

Бренд: 3Com Страницы: 2

852-112/000-001

Бренд: WAGO Страницы: 30

Premasreg 716 Series

Бренд: S+S Regeltechnik Страницы: 32

Бренд: G-Lab Страницы: 12

Бренд: H3C Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды