Cisco ASR 907 Скачать руководство пользователя страница 35

Страница: 35 / 204

1-port OC-48/STM-16 or 4-port OC-12/OC-3 / STM-1/STM-4 + 12-Port T1/E1 + 4-Port T3/E3 CEM
Interface Module (A900-IMA3G-IMSG)

The A900-IMA3G-IMSG interface module supports:

• 12xDS1/E1 + 4xDS3/E3 interface over the high-density port.

• 1xOC48/12/3 Gigabit interface and 3xOC12/3 Gigabit interface.

If OC48 is enabled, then the remaining 3 ports are disabled.

Note

Figure 21: A900-IMA3G-IMSG Gigabit Ethernet Interface Module

For information on supported SFP modules, see

Cisco ASR 900 Series Aggregation Services Routers Data

Sheet

1-Port OC-192 or 8-Port Low Rate CEM Interface Module (10G HO / 10G LO) (A900-IMA8S1Z-CX)

The 1-port OC-192 interface module with 8-port low rate CEM interface module is a high density combination
interface module. This module supports 1 OC-192 port or 8 low rate CEM or 1 Gigabit Ethernet port.

Cisco ASR 907 Router Hardware Installation Guide

Cisco ASR 907 Router Overview

1-port OC-48/STM-16 or 4-port OC-12/OC-3 / STM-1/STM-4 + 12-Port T1/E1 + 4-Port T3/E3 CEM Interface Module (A900-IMA3G-IMSG)

Содержание ASR 907












































































































































































































Результаты поиска

Содержание ASR 907

Отзывы:

Похожие инструкции для ASR 907

Бренды по названию

Популярные бренды

Cisco ASR 907, Руководство по установке оборудования

Результаты поиска

Содержание ASR 907

Отзывы:

Похожие инструкции для ASR 907

Бренды по названию

Популярные бренды