Cisco ASR 907 Скачать руководство пользователя страница 101

Страница: 101 / 204

Description

PID

Power Cord for AC V2 Power Module (Australia), AS 3112

PWR-CAB-AC-AUS

Power Cord for AC V2 Power Module (Europe), CEE 7/7

PWR-CAB-AC-EU

Power Cord for AC V2 Power Module (Italy), CEI-23-50

PWR-CAB-AC-ITA

Power Cord for AC V2 Power Module (South Africa), SABS 164

PWR-CAB-AC-SA

Power Cord for AC V2 Power Module (UK), EN 60309-2

PWR-CAB-AC-UK

Power Cord for AC V2 Power Module (Israel), SI 32

PWR-CAB-AC-ISRL

Power Cord for AC V2 Power Module (China), GB2099.1/GB1002

PWR-CAB-AC-CHN

Power Cord for AC V2 Power Module (Brazil), NBR 14136

PWR-CAB-AC-BRA

Power Cord for AC V2 Power Module (Swiss), SEV 1011

PWR-CAB-AC-SUI

Power Cord for AC V2 Power Module (Japan), JIS C8303

PWR-CAB-AC-JPN

India AC Power Cord for Cisco ASR 900, IS:1293

PWR-CAB-AC-IND

AC POWER CORD, WIRE HARNESS, Argentina, IRAM 2073, IEC60320
C21, ST, 4M, 30 AWG, STRANDED, 250.0 V, 16.0 A

PWR-CAB-AC-ARG

Activating the AC Power Supply

Follow these steps to activate the AC power supply:

Procedure

Step 1

Plug the power cord into the power supply.

Step 2

Connect the other end of the power cord to an AC-input power source.

Step 3

Verify power supply operation by checking that the power supply LEDs are in the following states:

• INPUT OK LED is green
• OUTPUT FAIL LED is green

Step 4

If the LEDs indicate a power problem, see the Troubleshooting for troubleshooting information.

Step 5

If you are installing a redundant power supply, repeat these steps for the second power source.

If you are installing a redundant AC power supply, ensure that each power supply is connected to
a separate power source in order to prevent power loss in the event of a power failure.

Note

Removing and Replacing the AC Power Supply

This section describes how to remove and replace the AC power supply.

Cisco ASR 907 Router Hardware Installation Guide

Installing the Cisco ASR 907 Router

Activating the AC Power Supply

Содержание ASR 907












































































































































































































Результаты поиска

Содержание ASR 907

Отзывы:

Похожие инструкции для ASR 907

Бренды по названию

Популярные бренды

Cisco ASR 907, Руководство по установке оборудования

Результаты поиска

Содержание ASR 907

Отзывы:

Похожие инструкции для ASR 907

Бренды по названию

Популярные бренды