Cisco ASR 907 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 204

background image

Class 1 CDRH) and Class 1M (IEC) laser products. Statement 1055

Warning

Invisible laser radiation may be emitted from the end of the unterminated fiber cable or connector. Do not
view directly with optical instruments. Viewing the laser output with certain optical instruments (for example,
eye loupes, magnifiers, and microscopes) within a distance of 100 mm may pose an eye hazard. Statement
1056

Warning

Safety with Electricity

Before working on a chassis or working near power supplies, unplug the power cord on AC units; disconnect
the power at the circuit breaker on DC units. Statement 12

Warning

Before working on equipment that is connected to power lines, remove jewelry (including rings, necklaces,
and watches). Metal objects will heat up when connected to power and ground and can cause serious burns
or weld the metal object to the terminals. Statement 43

Warning

Do not work on the system or connect or disconnect cables during periods of lightning activity. Statement
1001

Warning

Before performing any of the following procedures, ensure that power is removed from the DC circuit.
Statement 1003

Warning

Read the installation instructions before connecting the system to the power source. Statement 1004

Warning

This product relies on the building’s installation for short-circuit (overcurrent) protection. For -48/-60 VDC
installation, the wire shall be 8 AWG minimum with a 40 A circuit breaker. Statement 1005

Warning

This product relies on the building’s installation for short-circuit (overcurrent) protection. For an AC installation,
ensure that the branch circuit breaker is rated a maximum 20A.

Warning

Cisco ASR 907 Router Hardware Installation Guide

34

Preparing for Installation

Safety with Electricity

«
...
42
43
44
45
46
...
»

Содержание ASR 907













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 907

Бренд: Quantum Страницы: 20

Sure Cross DX70

Бренд: Banner Страницы: 35

Бренд: Direct IP Страницы: 76

Бренд: 3Com Страницы: 50

Бренд: Eaton Страницы: 14

Бренд: Abocom Страницы: 63

Бренд: Idis Страницы: 16

Бренд: ZyXEL Communications Страницы: 2

Бренд: TRENDnet Страницы: 2

Бренд: TRENDnet Страницы: 2

Бренд: Amphenol Страницы: 43

Бренд: Telit Wireless Solutions Страницы: 37

Бренд: Thecus Страницы: 90

Бренд: National Instruments Страницы: 37

Intelligent Fire Integrator 4WRMB

Бренд: Johnson Controls Страницы: 70

Бренд: CYP Страницы: 16

Бренд: Sarian Systems Страницы: 8

Ethernet IP Interface MS6 SERIES

Бренд: SAF OPAL Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды