Cisco ASR 907 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 204

background image

Guidelines for DC-Powered Systems

Basic guidelines for DC-powered systems include the following:

• Each chassis power supply should have its own dedicated input power source. The source must comply

with the safety extra-low voltage (SELV) requirements in the UL 60950, CSA 60950, EN 60950, and
IEC 60950 standards.

• The circuit must be protected by a dedicated two-pole circuit breaker. The circuit breaker should be sized

according to the power supply input rating and local or national code requirements.

• The circuit breaker is considered the disconnect device and should be easily accessible.
• The system ground is the power supply and chassis ground.
• Do not connect the DC return wire to the system frame or to the system grounding equipment.
• Use the grounding lug to attach a wrist strap for ESD protection during servicing.

Guidelines for AC-Powered Systems

Basic guidelines for AC-powered systems include the following:

• Each chassis power supply should have its own dedicated branch circuit.
• The circuit breaker should be sized according to the power supply input rating and local or national code

requirements.

• The AC power receptacles used to plug in the chassis must be the grounding type. The grounding

conductors that connect to the receptacles should connect to protective earth ground at the service
equipment.

Installing the DC Power Supply

The following sections describe how to install a DC power supply in the Cisco ASR 907 Router:

This equipment is suitable for installation in Network Telecommunications Facilities and locations where the
NEC applies.

Note

This equipment is suitable for installations utilizing the Common Bonding Network (CBN).

Note

The grounding architecture of this product is DC-Isolated (DC-I) for DC-powered products. DC-powered
products have a nominal operating DC voltage of 48 VDC.

Note

Installing the DC Power Supply Module

Perform the following procedure to install the power supply module:

Cisco ASR 907 Router Hardware Installation Guide

84

Installing the Cisco ASR 907 Router

Guidelines for DC-Powered Systems

«
...
92
93
94
95
96
...
»

Содержание ASR 907













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 907

Бренд: Supermicro Страницы: 24

Бренд: Allied Telesis Страницы: 1

Бренд: E-Lins Страницы: 9

Бренд: ZyXEL Communications Страницы: 2

Бренд: NETGEAR Страницы: 2

Бренд: Perle Страницы: 2

Бренд: Z Microsystems Страницы: 51

Бренд: Moxa Technologies Страницы: 51

FieldPoint FP-3000

Бренд: National Instruments Страницы: 118

Бренд: Teletronics International Страницы: 57

TeleCLIENT TC7730 Series

Бренд: ETL Страницы: 83

Бренд: INNOSILICON Страницы: 11

Бренд: Zhone Страницы: 2

Бренд: National Instruments Страницы: 26

Бренд: Tripp Lite Страницы: 3

Бренд: SriHome Страницы: 12

Бренд: NETGEAR Страницы: 20

GlobeSurfer X-1

Бренд: Option Audio Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды