Cisco ASR 907 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 204

background image

Figure 22: OC-192 Interface Module

Figure 23: OC-192 Interface Module Faceplate

The OC-192 interface modules are supported on slots 2, 3, 4 and 5 on the chassis.

Ports on the OC-192 are numbered from 1 to 8.

• Ports 0 to 7 are multi-rate ports, that support OC-3, OC-12, OC-48, Fast Ethernet interfaces, and the 1

Gigabit Ethernet interfaces.

• Port 8 is the 10 Gigabit Ethernet port that supports the OC-192 interfaces.

Port Restrictions

• The SFP+ port configuration is supported only on OC-192 interfaces port. If this port is enabled, other

SFP ports cannot be used (see the table given in Port Combinations Usage Guidelines section).

• Each SFP port can be configured for SONET or Ethernet.
• SFP ports configuration parameter, (see the table given in Port Combinations Usage Guidelines section):

• Maximum of 4 x OC-48 interfaces are supported per interface module
• For each OC-48 port enabled, neighboring SFP ports cannot be configured
• OC-3 and OC-12 port configuration is supported on all ports simultaneously
• 1 Gigabit Ethernet port configuration is supported on all ports simultaneously

1 Gigabit Ethernet port configuration is not supported.

Note

• Seamless migration from SONET to 1 Gigabit Ethernet interfaces is supported on all SFP ports

Cisco ASR 907 Router Hardware Installation Guide

26

Cisco ASR 907 Router Overview

Port Restrictions

«
...
34
35
36
37
38
...
»

Содержание ASR 907













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 907

Netlink FRX8000

Бренд: Cabletron Systems Страницы: 94

MMAC-Plus 9E423-24

Бренд: Cabletron Systems Страницы: 10

MMAC-Plus 9A128-01

Бренд: Cabletron Systems Страницы: 22

Spectrum EMM-E6

Бренд: Cabletron Systems Страницы: 2

SmartSTACK ELS100-24TXG

Бренд: Cabletron Systems Страницы: 112

Бренд: Cabletron Systems Страницы: 86

Бренд: Cabletron Systems Страницы: 54

Cabletron BRIM-F6

Бренд: Cabletron Systems Страницы: 43

Netlink FRX4000

Бренд: Cabletron Systems Страницы: 60

CSX200 CyberSWITCH

Бренд: Cabletron Systems Страницы: 2

Бренд: Cabletron Systems Страницы: 8

Бренд: Cabletron Systems Страницы: 4

Бренд: Paradyne Страницы: 2

Бренд: Paradyne Страницы: 20

Бренд: Paradyne Страницы: 2

Бренд: Zhone Страницы: 2

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 155

COMSPHERE 6800 Series

Бренд: Paradyne Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды