Cisco ASR 907 Скачать руководство пользователя страница 99 | Manualshive

Страница: 99 / 204

background image

Step 3

Switch the power supply circuit-breaker switch to the Off (O) position.

Step 4

Pull the terminal block plug connector out of the terminal block head in the power supply.

Step 5

Loosen the captive screws on the DC power supply.

Step 6

Grasping the power supply handle with one hand, pull the power supply out from the chassis while supporting
it with the other hand.

Step 7

Replace the DC power supply within 5 minutes. If the power supply bay is to remain empty, install a blank
filler plate (Cisco part number A900-PWR-BLANK) over the opening, and secure it with the captive installation
screws.

Installing the AC power Supply

This product requires short-circuit (over current) protection, to be provided as part of the building installation.
Install only in accordance with national and local wiring regulations.

Warning

Installing the AC Power Supply Module for A900-PWR1200-A (1200 W)

Follow these steps to install the power supply module:

Procedure

Step 1

Ensure that the system (earth) ground connection has been made. For ground connection installation instructions,
see the

Installing the Chassis Ground Connection

Step 2

If necessary, remove the blank power supply filler plate from the chassis power supply bay opening by
loosening the captive installation screws.

Step 3

Grasp the power supply handle with one hand. Place your other hand underneath the power supply, as shown
in the figure below. Slide the power supply into the power supply bay. Make sure that the power supply is
fully seated in the bay.

Cisco ASR 907 Router Hardware Installation Guide

89

Installing the Cisco ASR 907 Router

Installing the AC power Supply

«
...
97
98
99
100
101
...
»

Содержание ASR 907













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 907

Бренд: D-Link Страницы: 12

Бренд: Makita Страницы: 2

8BIG RACK THUNDERBOLT 2

Бренд: LaCie Страницы: 28

BladeCenter Management Module

Бренд: IBM Страницы: 184

SW-UNM-24FE2GC-24POE

Бренд: Morrell Страницы: 8

ipRocketLink 3086FR

Бренд: Patton electronics Страницы: 12

Бренд: Juniper Страницы: 420

DVI-Vision-IP-Fiber

Бренд: G&D Страницы: 240

Бренд: Hamlet Страницы: 11

Бренд: netsys Страницы: 164

Бренд: Spirent Страницы: 22

NVR2104/2108HS-W-4KS2 1U

Бренд: Dahua Technology Страницы: 363

Бренд: Idis Страницы: 16

Бренд: VERTO Страницы: 48

Бренд: AIC Страницы: 79

RouteFinder RF560VPN

Бренд: Multitech Страницы: 82

Бренд: Vivotek Страницы: 13

I-FLY A02-WRA4-54G

Бренд: Atlantis Land Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды