Cisco ASR 907 Скачать руководство пользователя страница 92 | Manualshive

Страница: 92 / 204

background image

2.

Scans the backplane for configuration changes.

3.

Initializes the newly inserted module. In addition, the system notes any removed modules and places those
modules in the administratively shutdown state.

4.

Places any previously configured interfaces on the module back to the state they were in when they were
removed.

The router runs diagnostic tests on any new interfaces and the test results indicate the following:

• If the tests pass, the router is operating normally.

• If the new module is faulty, the router resumes normal operation but leaves the new interfaces disabled.

• If the diagnostic tests fail, the router stops operating, which usually indicates that the new module has a

problem in the bus and should be removed.

To avoid erroneous failure messages, note the current configuration of all interfaces before you remove or
replace an interface module, and allow at least 2 minutes for the system to reinitialize after a module has been
removed or replaced. This time is recommended in order to allow for synchronization between components
within the interface module and for synchronization with the standby RSP.

Caution

Installing the Power Supply

The Cisco ASR 907 Router router provides the choice of two different power supplies:

• 1200 W DC power: - 40.8VDC to -72VDC

The DC power supply uses 3 position terminal block-style connector with positive latching/securing and
labeled connections for 48V, GRD, 48V. The terminal block connector is of suitable size to carry the
appropriate AWG wire size to handle the input current of the power supply. No ON/OFF switch is
provided.

• AC power: 85VAC to 264VAC

The AC power supply has an IEC-320-C21-type power receptacle and a 20 A service connector. You
can use standard right angle power cords with the AC power supply. The power supply includes a power
cord retainer. No ON/OFF switch is provided.

The power supply must be wired before plugging the power supply in the chassis. Ensure the branch circuit
breaker is turned off. Only after installing the power supply in the chassis, should the branch circuit breaker
be turned on. The branch circuit breaker must be turned off before unplugging the power supply.

Caution

Each power supply provides a single primary input power connection. You can install dual power supplies
for redundancy.

Read the installation instructions before connecting the system to the power source. Statement 10

Warning

Cisco ASR 907 Router Hardware Installation Guide

82

Installing the Cisco ASR 907 Router

Installing the Power Supply

«
...
90
91
92
93
94
...
»

Содержание ASR 907













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 907

Бренд: NEC Страницы: 8

8 Port 10/100Mbit/s Ethernet Smart Switch with Fibre Uplink

Бренд: Tyco Electronics Страницы: 18

Бренд: F5 Страницы: 2

Бренд: F5 Страницы: 90

Бренд: F5 Страницы: 47

Бренд: Qualys Страницы: 2

ROADRECORDER 8000

Бренд: Safety Vision Страницы: 40

Бренд: JUMO Страницы: 60

3C8567 - SuperStack II NETBuilder SI 567...

Бренд: 3Com Страницы: 6

Ether-GSH24T v3

Бренд: AirLive Страницы: 2

Бренд: Sierra Wireless Страницы: 2

Бренд: NETGEAR Страницы: 152

Бренд: LaView Страницы: 2

Dynalink MyZone 3G24W

Бренд: NetComm Страницы: 5

Бренд: Alloy Страницы: 13

Бренд: Ubiquiti Страницы: 13

Compressor DW-CP04

Бренд: Digital Watchdog Страницы: 73

Magnum mP62-5V -1M1SSC

Бренд: GarrettCom Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды