Cisco ASR 907 Скачать руководство пользователя страница 88

Страница: 88 / 204

Installing the Interface Module Carrier

It is recommended that you always install the IM carrier (A9XX-2IMA-CARRIER) in the lower slot before
installing the carrier in the upper slot.

Note

Procedure

Step 1

Before inserting an IM carrier, make sure that the chassis is grounded.

Step 2

To insert the IM carrier, carefully align the edges of the IM carrier between the upper and lower edges of the
router slot.

Step 3

Carefully slide the IM carrier into the router slot until the IM carrier makes contact with the backplane. See
the figure below.

Figure 50: Installing the IM Carrier

Interface Module Installation

The following sections describe the various tasks of associated with interface module installation on the Cisco
ASR 907 Router:

Cisco ASR 907 Router Hardware Installation Guide

Installing the Cisco ASR 907 Router

Installing the Interface Module Carrier

Содержание ASR 907












































































































































































































Результаты поиска

Содержание ASR 907

Отзывы:

Похожие инструкции для ASR 907

Бренды по названию

Популярные бренды

Cisco ASR 907, Руководство по установке оборудования

Результаты поиска

Содержание ASR 907

Отзывы:

Похожие инструкции для ASR 907

Бренды по названию

Популярные бренды