Cisco ASR 907 Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 204

background image

Failure to securely tighten the power and relay connector captive screws can result in an electrical arc if the
connector is accidentally removed. Statement 1058

Warning

This equipment is intended to be grounded. Ensure that the host is connected to earth ground during normal
use.

Warning

If you connect or disconnect the console cable with power applied to the switch or any device on the network,
an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that
power is removed or the area is nonhazardous before proceeding. To verify switch operation, perform POST
on the switch in a nonhazardous location before installation. Statement 1065

Warning

Installation of the equipment must comply with local and national electrical codes. Statement 1074

Warning

Hazardous voltage or energy may be present on DC power terminals. Always replace cover when terminals
are not in service. Be sure uninsulated conductors are not accessible when cover is in place. Statement 1075

Warning

When working on equipment powered by electricity, follow these guidelines:

• Locate the room’s emergency power-off switch. If an electrical accident occurs, you will be able to

quickly turn off the power.

• Before working on the system, turn off the DC main circuit breaker and disconnect the power terminal

block cable.

• Before doing the following, disconnect all power:

• Working on or near power supplies
• Installing or removing a router chassis or network processor module
• Performing most hardware upgrades

• Never install equipment that appears damaged.
• Carefully examine your work area for possible hazards, such as moist floors, ungrounded power extension

cables, and missing safety grounds.

• Never assume that power is disconnected from a circuit; always check.
• Never perform any action that creates a potential hazard to people or makes the equipment unsafe.
• If an electrical accident occurs, proceed as follows:

• Use caution, and do not become a victim yourself.
• Turn off power to the router.
• If possible, send another person to get medical aid. Otherwise, determine the condition of the victim,

and then call for help.

• Determine whether the person needs rescue breathing or external cardiac compressions; then take

appropriate action.

Cisco ASR 907 Router Hardware Installation Guide

37

Preparing for Installation

Safety with Electricity

«
...
45
46
47
48
49
...
»

Содержание ASR 907













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 907

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 2

Бренд: ICP DAS USA Страницы: 8

Бренд: TRENDnet Страницы: 2

Бренд: Allnet Страницы: 12

Бренд: Telebyte Страницы: 19

Fan Tray 8820-S2-900

Бренд: Paradyne Страницы: 6

Бренд: 1&1 Страницы: 32

WNFB-265AXI(BT)

Бренд: Sparklan Страницы: 14

Бренд: Nilox Страницы: 66

Бренд: Z-Com Страницы: 18

Бренд: Compro Technology Страницы: 2

Бренд: Korenix Страницы: 25

Бренд: Top Страницы: 21

Ether-GSH24T v3

Бренд: AirLive Страницы: 2

Бренд: SriHome Страницы: 12

DynaGST/2402G GEP-33224T-1

Бренд: UNICOM Страницы: 17

CU8210-D001-0200

Бренд: Beckhoff Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды