Cisco ASR 907 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 204

background image

Removing and Replacing the Fan Tray

The fan tray supports online insertion and removal (OIR). There is no need to power down the Cisco ASR
907 Router to remove or replace the fan tray. However, the router will shut down if the fan tray is removed
from the chassis for more than 90 seconds at 25º C due to thermal overload condition. Approximately at 25º
C the system powers back in 2 minutes.

If a fan tray is removed and not replaced within the stipulated time the system will automatically power-off.
If the system is powered with PSUs other than 900W DC or 1200W AC and if the system is powered off,
then the system should be completely powered off for 30 seconds with all the PSU in the system simultaneously,
and then turned on for the system to power on.

Note

Do not introduce body parts or objects in the fan tray slot when installing or removing the fan tray module.
Exposed circuitry is an energy hazard.

Note

The router can stay active for up to 60 seconds if the temperature is up to 30º C. However, in the event of an
overtemperature alarm, the router can shut down in less than 60 seconds. In the event of a critical temperature
alarm, the router shuts down immediately.

Caution

To avoid erroneous failure messages, allow at least 2 minutes for the system to reinitialize after the fan tray
has been replaced.

Caution

Follow these steps to remove and replace the fan tray on the Cisco ASR 907 Router:

Procedure

Step 1

Using a No. 2 Phillips screwdriver or your fingers, loosen the captive installation screw that secures the fan
tray to the chassis. The figure below shows the front of the fan tray, including the captive installation screws.

Cisco ASR 907 Router Hardware Installation Guide

72

Installing the Cisco ASR 907 Router

Removing and Replacing the Fan Tray

«
...
80
81
82
83
84
...
»

Содержание ASR 907













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для ASR 907

Бренд: D-Link Страницы: 267

Бренд: Patton electronics Страницы: 8

Бренд: ZyXEL Communications Страницы: 116

Бренд: B&B Electronics Страницы: 2

SRA311-008P8 Series

Бренд: Divio Страницы: 4

Бренд: Pakedge Device & Software Страницы: 14

AceroDURO 100/S100

Бренд: CNC-Step Страницы: 86

Бренд: BinTec Страницы: 2

Xtreme Networked Boat

Бренд: Broadband Products Страницы: 16

Бренд: LanReady Страницы: 40

Бренд: NAVI Страницы: 18

Бренд: Hitachi Страницы: 52

Бренд: Hitachi Страницы: 58

Бренд: Hitachi Страницы: 68

Бренд: Hitachi Страницы: 85

Бренд: Hitachi Страницы: 76

Бренд: Hitachi Страницы: 98

Бренд: Hitachi Страницы: 192

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды