Cisco ASR 907 Скачать руководство пользователя страница 14

Страница: 14 / 204

The Cisco ASR 907 Router (with industrial temperature optics) supports the
following temperature ranges at 1800 m operating altitude:

• -40º C to 65º C

Operating Temperature

-40º F to 158º F (-40º C to +70º C) storage temperature

Nonoperating Temperature

5–95% operating non-condensing relative humidity

Operating Humidity

-60 m to 1800 m operating altitude for full operating temperature range; up to 4000
m at up to 40º C.

Operating Altitude

-60 m to 4570 m storage altitude

Nonoperating Altitude

1.0 g from 1.0 to 150 Hz

Vibration

30 G half sine 6 ms and 11 ms

Shock

Random: 1.15 g RMS 3 to 200 Hz, 30 minutes/axis

Sine: 10 to 500 Hz at 0.8 G peak / 5 sweep cycles/axis

Nonoperating Vibration

< 76 dBA at 27ºC as per NEBS standard GR-63

Operating Acoustics

GNSS Module (A900-CM-GNSS)

The GNSS module is present on the RSP. It is a pluggable module that allows direct interface with the external
antenna.

Using a single GPS antenna input for both RSPs requires usage of external splitters.

Note

To reduce the risk of fire, use only No. 26 AWG or larger telecommunication line cord. Statement 1023

Warning

The GNSS module is not hot swappable.

Note

GNSS Module RF Input Requirements

• The GNSS module requires an active GPS/GNSS antenna with built-in Low-Noise Amplifier (LNA) for

optimal performance. The antenna LNA amplifies the received satellite signals for two purposes:

• Compensation of losses on the cable
• Lifting the signal amplitude in the suitable range for the receiver frontend

The Amplification required is 22dB gain + cable/connector loss + Splitter signal loss.

The recommended range of LNA gain (LNA gain minus all cable and connector losses) at the connector
of the receiver module is 22dB to 30dB with a minimum of 20dB and a maximum of 35dB.

Cisco ASR 907 Router Hardware Installation Guide

Cisco ASR 907 Router Overview

GNSS Module (A900-CM-GNSS)

Содержание ASR 907












































































































































































































Результаты поиска

Содержание ASR 907

Отзывы:

Похожие инструкции для ASR 907

Бренды по названию

Популярные бренды

Cisco ASR 907, Руководство по установке оборудования

Результаты поиска

Содержание ASR 907

Отзывы:

Похожие инструкции для ASR 907

Бренды по названию

Популярные бренды