Cisco aironet 1240 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 216

background image

3-13

Cisco 1240 Connected Grid Router Hardware Installation Guide

OL-26223-04

Chapter 3 Router Hardware Description

Hardware Features Detailed Description

Chassis Cable Ports

The router chassis has the following cable ports for router network and power cables:

•

Door

—Two cable ports on the front door, shown in

Figure 3-2

, provide support for third party radio

cabling. The router supports installation of a compatible radio, as described in the

“Installing

External Non-Cisco Modules” section on page 13-1

.

•

Chassis

—Seven cable ports on the router base, shown in

Figure 3-7

, provide support for router

network cabling, as described in the

“Installing the Router”

chapter.

Cable Glands

A cable gland (also known as a cable connector) is required to install cables in the chassis cable ports.
Use a compatible cable gland to attach and secure the end of a cable to the router. The cable gland
provides cable strain relief and seals the cable entry into the router chassis to prevent damage to the
router interior.

Figure 3-9

Cable Gland

Specifications

Cable Port Seals

Unused router ports are sealed with a liquid-tight cover (PG13) to protect the router interior from
environmental elements.

Caution

The router should not be installed unless all unused chassis cable ports are sealed. Leaving chassis ports
unsealed can damage the router.

Table 3-9

Supported Cisco Cable Glands

Cisco Product ID

Description

CGR-IP67GLAND

Contains 1 gland and 1 tube of anti-seize compound

Specification

Description

Size

PG 13

Cable diameters: 0.20-0.35 inches (5.08-8.89 mm)

Environmental

Liquid Tight Type 4x & IP67

300541

«
...
31
32
33
34
35
...
»

Содержание aironet 1240

























































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для aironet 1240

Бренд: Idis Страницы: 123

Бренд: Idis Страницы: 29

Бренд: Idis Страницы: 28

DirectIP DR-1304P

Бренд: Idis Страницы: 82

Бренд: iDirect Страницы: 130

Бренд: N-Tron Страницы: 62

Бренд: Vivotek Страницы: 136

Бренд: N.A.T. Страницы: 32

AIE900-XNX Series

Бренд: AXIOMTEK Страницы: 53

RabbitCore RCM4400W

Бренд: Rabbit Страницы: 126

ControlPoint 2000

Бренд: 4Home Страницы: 20

Бренд: TRENDnet Страницы: 10

Бренд: Konica Minolta Страницы: 31

Network Adapter AC AAP

Бренд: Extron electronics Страницы: 2

Бренд: DayTronic Страницы: 13

Cyclades CS4008

Бренд: Avocent Страницы: 2

Бренд: Renesas Страницы: 7

CNPS7000B Series

Бренд: ZALMAN Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды