| P
age 32 | SEABOB Operation Manual |
5
| P
age 33 | SEABOB Operation Manual |
5
|
Online Version
|
|
Online Version
|
5.3.4 Information display
The graphic display is divided into three fields. Dur-
ing operation of the craft, the following information is
shown in the information display:
Left field:
The current water temperature (in °C) is shown at the
top left of the display. Below, the current diving depth (in
m) is displayed.
Middle field:
The power display is located in the middle field. The
current motor speed is depicted graphically in the
speed range on the outer circle. The red dot in the speed
range shows the maximum power (Power Level) set in
the menu. The current power (Power Level) is shown
numerically and graphically in six successive segments
on the inner circle. The sixth segment (Power Level 6) is
shown in red, all of the preceding segments are shown
in white. The numerical display of the current power
in % of maximum power is displayed in the centre of the
power display.
The current Power Level and the current power in % of
maximum power are set parallel to each other. The power
is set in increments of 15 % and 25 % (6 Power Level).
Power is increased by one Power Level by tapping the
green button (+ 15% or + 25 %) and decreased by one
Power Level by tapping the red button (- 15 % or - 25 %).
Note:
When the SEABOB is switched on, the set maxi-
mum diving depth is shown at the bottom of the power
display for 10 seconds. This information then disappears
again.
In the event of a malfunction, additional symbols may
appear in the middle field. Below is a list of these sym-
bols and their descriptions:
Warning symbol
• Motor temperature warning ("motor overheated")
➞
Power is limited to Power Level 2
• Accumulator temperature warning ("accumulator
overheated")
➞
Power is limited to Power Level 2
• Warning: Accumulator error ("accumulator error")
➞
Emergency operation! Power is limited to Power Level 2
Should the accumulator error re-occur or be-
come permanent, immediately halt operation
and contact the manufacturer or your specialist dealer
without delay.
• Warning: Impeller locked ("impeller locked")
➞
Motor stops
➞
see Chapter 7.4 "Impeller does not
turn (no thrust)"
Workshop symbol
• Warning: Water ingress into accumulators or elec-
tronics ("warning water ingress")
➞
Motor stops
➞
SEABOB switches to Off mode after 5 seconds
• Warning: System error ("system error")
➞
Trigger
or Controlgrip error / internal communication inter-
rupted
➞
Motor stops
➞
Contact manufacturer or specialist dealer!
Right field:
In the right-hand field there is an accumulator symbol
with individual bars showing the charge state of the
SEABOB (1 bar = 10 % charge state). The numerical
display of the charge state (in % of full charge state) is
located above this symbol. The temperature of the accu-
mulator (in °C) is shown below the accumulator symbol.
Left
field
Middle
field
Right
field
Accumulator
temperature
(in °C)
Water
temperature
Diving depth
Set maximum
diving depth
Power (in % of
maximum power)
Power
Level
Speed range with red dot
for set maximum power
Accumulator
charge state
(in % of full
charge state)
Time Display:
Tap the blue button on the right Controlgrip while the
power is displayed as "0 %" in the power display. The
time display appears.
The operating time of the SEABOB in the On mode ("on
mode") is shown in the centre of the display in the fol-
lowing order:
• Operating time during the last operation ("last")
• Operating time during the current day ("day")
• Total operating time ("total")
Note:
The operating time during the last operation
("last") shows the operating time of the SEABOB from
the last time it was switched on (On mode) until it was
last switched off (Sleep mode / Off mode).
Note:
In order to guarantee the operating time during
the current day ("day") is measured accurately, please
always ensure that the stored time is adjusted to the cur-
rent local time. The operating time during the current day
("day") shown in the display is reset daily at midnight.
In order to exit the time display, tap the blue button
again. The information display appears in the display of
the SEABOB.
Timer:
Tap the blue button on the right Controlgrip while the
power display is at a minimum power of "15 %" (Power
Level 1). The timer appears.
The speed range as well as the set maximum power
(Power Level) (marked in red) are shown as before in the
middle field of the display on the outer circle. The follow-
ing information is displayed inside as an alternative to
the information display:
• Current power in 6 Power Level ("power level")
• Operating time since it was switched on
(in hrs:min’sec)
Note:
When the timer is activated to limit the operat-
ing time, the timer display is always shown in the dis-
play. Instead of the operating time since the device was
switched on, the remaining operating time is shown here
(in hrs:min’sec).
Note:
The set current mode ("on mode" or "timer") is
displayed for 10 seconds after switching to the timer dis-
play. After this time, it is replaced by the set maximum
diving depth. The information disappears after 30 sec-
onds.
In order to exit the timer display, tap the blue button
again. The information display appears in the display of
the SEABOB.
Timer
Time Display
Содержание seabob f5 S
Страница 1: ...Online Version English User manual Online Version...
Страница 36: ...Online Version www seabob com...
