| P
age 34 | SEABOB Operation Manual |
5
| P
age 35 | SEABOB Operation Manual |
5
|
Online Version
|
|
Online Version
|
5.3.5 Off mode (air transport / storage) –
switching on / off
Special safety precautions must be taken before trans-
porting the craft, particularly by aircraft. The current
flowing to the accumulator must be cut off, and precau-
tions must be taken to ensure that the device cannot be
switched on inadvertently or incorrectly. For safety rea-
sons, the SEABOB cannot be switched back on when it is
in Off mode by tapping the device‘s buttons. It can only
be switched on using a connected and active charger.
When the SEABOB is in Sleep mode, however, it can be
switched back on using the device‘s buttons.
Switching off to Off mode:
Switching off to Off mode can only be done using a con-
nected and active charger. To switch off to Off mode,
proceed as follows, taking into account the information
contained in Chapter 5.2 "Charging the SEABOB":
1. Plug the connector into the connection port on the
SEABOB.
2. Plug the mains plug into the mains socket.
3. The charge display will appear in the display after a
brief system check.
4. Tap the green button for partial charging of the
SEABOB to the charge state "air transport / storage"
(a partially filled charge symbol will appear in the
display).
5. When the aircraft symbol appears in the display,
the charge state for air transport / storage has been
reached.
6. To save energy and to reduce maintenance charging,
the display turns itself off automatically 10 minutes
after charging is completed (“complete”). By pressing
any button, the display can be switched on again (for
another 10 minutes).
7. If you disconnect the charger from the connection
port, the SEABOB will switch off to Off mode after
5 seconds (system check), regardless of the current
charge state and even if the correct charge state for
air transport / storage has not been reached.
For this reason, you should follow the instruc-
tions given in Chapter 5.10 "Storing the SEABOB"
and Chapter 5.11 "Air transport / transport of the
SEABOB" on correctly switching off the device to
Off mode for air transport and storage.
Note:
If the accumulator charge state is too high prior
to starting the partial charging process for air transport /
transport, you will have to perform an automatic dis-
charge by means of a connected and active charger (may
take up to 24 hours) or by running the SEABOB to empty
in a controlled fashion as described in Chapter 5.11.
Switching on from Off mode:
When the system is in Off mode, it can only be switched
back on by initiating the charging process.
1. Plug the connector into the connection port on the
SEABOB.
2. Plug the mains plug into the mains socket.
3. Activation of the SEABOB is triggered by the inde-
pendent electronic control system in the accumula-
tors together with a correctly detected charger (sys-
tem check).
4. The charge display will appear in the display. The
SEABOB is now in Charge mode.
5. Decide how to proceed using the green or red button
(see Chapter 5.3.7 "Charge mode" and Chapter 5.3.8
"Charge display").
Manual switching off to Sleep mode:
You can also switch the SEABOB to Sleep mode manually.
To do so, proceed as follows:
1. The information display is shown in the display. The
power is displayed as “0 %” in the power display.
2. Tap the button combination silver – blue in quick
sequence. The prompt "sleep mode - confirm with
trigger" appears.
3. If the user activates the Trigger within 5 seconds, the
system will switch to Sleep mode and switch off.
Note:
If the Trigger is not activated within 5 seconds, the
system will return to the last selected mode (e.g. infor-
mation display in the On mode).
5.3.6 Sleep mode / On mode – switching
on / off
In Sleep mode, the display and motor are switched off.
Switching on from Sleep mode:
1. Tap the blue button.
2. The display is switched on. The SEABOB logo and the
prompt "push trigger" appear.
3. Push the Trigger against the Controlgrip (within 5 sec-
onds). The SEABOB logo disappears again.
4. Release the Trigger completely. The User-PIN or Own-
er-PIN prompt will appear in the display (if activated).
If the PIN prompt has been deactivated, the informa-
tion display will appear directly.
Note
: After a prolonged phase of being idle, the sys-
tem will automatically start the motor initialization. The
motor will make two slow turns. The initialization takes
about 5 seconds.
5. The motor is switched on by pushing the Trigger (the
motor runs with a minimum power of Power Level 1).
Note:
If the Trigger is not activated within 5 seconds af-
ter tapping the blue button during activation, the display
will switch off again (device reverts to Sleep mode).
Note:
If you want to activate the PIN prompt when
switching on the device, or if you want to activate and
change the User-PIN, proceed as described in Chapter
5.3.11 "Settings".
Automatic switching off to Sleep mode (Time-off):
If no actions are performed by the user within 10 min-
utes (Time-off), the system will switch off automatically
to Sleep mode.
Содержание seabob f5 S
Страница 1: ...Online Version English User manual Online Version...
Страница 36: ...Online Version www seabob com...
