Case CX300C, Руководство оператора

Страница: 131 / 288

4 - OPERATING INSTRUCTIONS
4 - OPERATING INSTRUCTIONS ###_4_###
COMMISSIONING THE UNIT
Cab - Operating
Before using the machine
DANGER
Improper operation or service of this machine
can result in an accident.
Do not operate this machine or perform any
lubrication, maintenance, or repair on it until
you have read and understood the operation,
lubrication, maintenance, and repair informa-
tion.
Failure to comply will result in death or seri-
ous injury.
D0010A
Before operating this machine, be sure to do the
following:
1. Check the level of all fluids (engine oil, hydraulic fluid
and coolant) and make sure that the fluids and lubri-
cants are suitable for prevailing conditions. (Refer to
pages
6-5 and 4-11 ).
2. Carry out the daily maintenance operations. (Refer
to page
6-1 ).
3. Inspect the machine, look for any signs of possible
leakage and check the hoses. Tighten or replace as
necessary.
4. Refer to page 4-3 if the machine is new or if the en-
gine has been reconditioned.
5. Check the track assemblies. (Refer to page 6-50 ).
6. Clean the steps and access handles. Grease, oil,
mud or ice (in winter) on the steps and access han-
dles can causes accidents. Make sure they are kept
clean at all times.
7. Clean or replace any decals which are illegible. (Re-
fer to page
2-8 ).
8. Make sure that the engine hood and the side doors
are properly closed and latched.
9. Secure the cab door in either fully closed or fully
opened position. (Refer to page
3-1 ).
10. Remove any obstructions which hinder visibility.
Clean the windshield, the windows and the rear view
mirrors.
11. Check that no tools or other items have been left
on the machine (be it on the undercarriage or the
upperstructure) or in the operator's compartment.
12. Make sure nobody is on or under the machine. The
operator must be alone on the machine.
13. Make sure nobody is standing in the machine work-
ing area.
14. Find out about current safety measures in use on the
work site.
15. Work out a convenient means of escape from the
machine (emergency exit via the windshield, the rear
window glass) in the event of the machine turning
over or tipping over or the cab door being jammed.
16. Before undertaking any travel or working operations
during hours of darkness, make sure the lighting and
signalling equipment is fully operative.
Operating the machine
WARNING
Driving hazard!
Check all controls and safety devices in a safe,
open area before starting work.
Failure to comply could result in death or se-
rious injury.
W0248A
When operating the machine, be sure to do the following:
1. When starting the engine, be sure to use the correct
procedure for the prevailing weather conditions. (Re-
fer to page
4-7 ).
2. Regularly consult the hourmeter to ensure that all
servicing operations are carried out punctually.
3. If you use your machine in particularly harsh condi-
tions (dusty or corrosive atmosphere), the servicing
intervals should be reduced accordingly.
4. Take note of the locations of pipes/cables before
starting work.
5. Do not work near overhead high-voltage electric lines
without checking beforehand that all necessary mea-
sures have been taken to respect the minimum dis-
tances:
Less than 57 000 volts:
3 m ( 9.8 ft )
More than 57 000 volts: 5 m ( 16.4 ft )
6. When working on a public highway, use standard
traffic signs and take into consideration the working
range of the upperstructure and its attachments. Lo-
cal regulations stipulate the number, type and loca-
tion of reflector strips.
7. Never operate the working or travel controls unless
you are properly seated in the operator's seat with
the seat belt correctly fastened.
8. Modify your driving to suit the type of work and work-
ing conditions.
4-1