cascade corporation 14J Series Скачать руководство пользователя страница 26

Страница: 26 / 58

6921413

SERVICE

4.4

Drive Group

(2.8 ci motor and greater)

4.4-1

Drive Group −

Removal and Installation

Remove the attachment from the truck as described in

Section 4.1.

Remove the four capscrews fastening the drive group to

the baseplate. For reassembly, tighten the capscrews

to 48 ft.-lbs. (66 Nm).

For reassembly, reverse the above procedures with the

following exceptions:
• After the drive group has been reinstalled, check the

gear case lubricant level. Lubricant must be up to

the bottom of the fill plug hole. If necessary, fill with

Cascade Gear Lube (Part No. 656300), or SAE 90

wt. gear lube (AGMA 'mild' 6 EP Gear Lube).

RR0520.eps

4.4-2

Drive Group –

Disassembly and Service

Remove the drive group from the baseplate as

described in Section 4.4-1.

Lay the drive group, pinon down, on two 4 x 4 in.

(10 x 10 cm) wood blocks placed on both sides of the

pinion.

Remove the four capscrews fastening the cover plate to

the housing.

Remove the center capscrew plug from the cover plate

and install a 3/8 NC capscrew (early) or M10 capscrew

(later) with a minimum of 2 in. (50 cm) thread length.

Remove the cover plate by turning the capscrew

clockwise while lightly tapping around the side of the

cover plate to lift it off the housing.

Drain oil from the housing.

Remove the three capscrews fastening the end cover to

the housing.

Remove the drive motor as described in Section 4.6-1.

RR0549.eps

Cover

Plate

Housing

4 3

Содержание 14J Series



























































Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды

cascade corporation 14J Series, Руководство по обслуживанию

Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды