cascade corporation 14J Series Скачать руководство пользователя страница 31

Страница: 31 / 58

6921413

SERVICE

RR0592.eps

RR0589.eps

4.5-2

Drive Motor Disassembly

Cascade provides service replacement parts for the seals

indicated with a

▲

below. Due to cost, if other parts need

replacement, the complete drive motor assembly should

be replaced.

Remove the drive motor from the drive group as

described in Section 4.5-1.

IMPORTANT:

Clean the outside of the drive

motor and service in a clean, dust-free work area.

Use a soft-jawed vise for all service procedures.

Make a scribe mark across the motor sections. This will

help with timing and alignment for reassembly.

Clamp the motor in a soft-jawed vise with the output

shaft facing upward.

Remove the three capscrews from the flange. Remove

the flange. Keep track of O-ring between the flange

and motor.

Remove the five capscrews with a 3/16 in. allen wrench

(hex key).

Disassemble the motor as shown below. The motor can

be taken apart in five groups.

Remove the bearing housing group. Remove the

output shaft from the bearing housing.

CAUTION:

Leave the thrust bearing and thrust

washer on the output shaft. Leave the output shaft

spacer in the output shaft.

Remove spool drive and drive.

Remove drive and spacer with O-ring.

Remove geroler set with O-ring.

CAUTION:

Geroler spacers can fall out if not

handled properly.

Leave the valve housing in the vice. Remove the

spool valve and O-ring from the valve housing.

CAUTION:

Do not remove retaining rings and check

balls from the spool valve.

Pressure Seal

▲

Wiper Seal

▲

Bearing Housing

Valve

Housing

Bearing

Housing

Group

Output Shaft

Spacer

Thrust Bearing

Thrust Washer

Output Shaft

Drive

▲

Replacement parts available through Cascade

Spool Drive

Spool
Valve

Geroler Set

Flange

Flange O-Ring

Spacer

Plate

Capscrews (5)

O-Ring

▲

O-Ring

▲

O-Ring

▲

RR0590.eps

RR0591.eps

Содержание 14J Series



























































Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды

cascade corporation 14J Series, Руководство по обслуживанию

Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды