cascade corporation 14J Series Скачать руководство пользователя страница 24

Страница: 24 / 58

6921413

SERVICE

RR0572.eps

RR0573.eps

RR0614.eps

RR0613.eps

4.3-3

Drive Group Reassembly

Build up the pinion/worm gear assembly vertically with the

pinion gear down.

Install pinion seal onto seal seating area.

Apply Loctite 271 (red) to the bearing seating area as

shown. Press housing bearing onto the pinion shaft.

Remove excess Loctite.

Install the key onto pinion shaft. Apply Loctite 271 (red)

to the pinion shaft. Install the worm gear, cover plate

pinion bearing and retaining ring of the pinion.

Apply Loctite 271 (red) to housing seating area and

shoulder for the housing pinion bearing. Install the

complete pinion assembly into the housing. Remove

excess Loctite.

CAUTION:

Make sure Loctite does not squeeze into the

seal or bearings.

Install the worm's bearing in the drive motor side of the

housing.

CAUTION:

Bearing is directional. Install bearing with

the part number side facing the motor.

Install the drive motor as described in Section 4.5-1.

Install the worm and second bearing in the housing.

Fully engage the worm with the drive motor shaft.

CAUTION:

Bearing is directional. Install bearing with

the part number side facing end cover.

Pinion

Gear

Key

Housing

Bearing

Seating

Area

Pinion

Seal

Housing

Pinion

Bearing

Worm Gear

Bearing

Snap Ring

PINION AND BEARING WITH EXTERNAL SEAL

Seal

Seating

Area

Содержание 14J Series



























































Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды

cascade corporation 14J Series, Руководство по обслуживанию

Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды