cascade corporation 14J Series Скачать руководство пользователя страница 33

Страница: 33 / 58

6921413

SERVICE

4.5-4

Drive Motor Reassembly

(Continued)

Apply a coating of a lithium based bearing grease,

such as Mobilith SCH220, to inner edges of wiper seal,

pressure seal, thrust bearing and washer.

Install wiper seal with the u-shape facing outward from

its seat. Press the wiper seal firmly into its seat.

CAUTION:

Do not damage seal. If seal is damaged

during installation, it must be replaced.

Install pressure seal with the u-shape facing outward

from its seat. Press the pressure seal firmly into the

seat. If needed, use a 1 in. (25 mm) diameter dowel to

press the seal.

CAUTION:

Do no damage seal. If seal is damaged

during installation, it must be replaced.

Place the output shaft onto the spool drive. Rock the

shaft around until the spool drive engages into the

output shaft spacer.

Install the bearing housing onto the output shaft while

aligning the scribe marks and screw holes.

CAUTION:

Do not damage seal. If seal is damaged

during installation, it must be replaced.

Install the five capscrews by pre-torquing them in an

alternating cross pattern to 7 ft.-lbs. (10 Nm). Final

torque in an alternating cross pattern to 11 ft.-lbs.

(15 Nm).

Lubricate the flange O-ring with petroleum jelly and

press into flange. Place flange on the shaft and flush

against the housing. Install capscrews and tighten to a

torque of 9.5 ft.-lbs. (13 Nm).

RR0775.eps

Pressure Seal

Wiper Seal

Bearing Housing

RR0598.eps

RR0599.eps

RR0600.eps

RR0601.eps

Flange O-Ring

Содержание 14J Series



























































Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды

cascade corporation 14J Series, Руководство по обслуживанию

Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды