cascade corporation 14J Series Скачать руководство пользователя страница 54

Страница: 54 / 58

6921413

SPECIFICATIONS

GA0397.eps

Truck Relief Setting

(see attachment nameplate)

2250 psi (155 bar)

Recommended

2755 psi (190 bar)

Maximum

NOTE:

The attachment revolving connection has separate

pressure relief control, see Section 4.9-3 for adjustment.

Truck Flow Volume

➀

Min.

➁

Recommended

Max.

➂

CLAMP

5 GPM

(19 L/min.)

12 GPM

(45 L/min.)

16 GPM

(61 L/min.)

ROTATE

5 GPM

(19 L/min.)

10 GPM

(38 L/min.)

15 GPM

(57 L/min.)

SIDESHIFT

5 GPM

(19 L/min.)

8 GPM

(32 L/min.)

12 GPM

(45 L/min.)

➀

Cascade Revolving attachments are compatible with SAE 10W

petroleum base hydraulic fluid meeting Mil. Spec. MIL-0-5606 or

MIL-0-2104B. Use of synthetic or aqueous base hydraulic fluid

is not recommended. If fire resistant hydraulic fluid is required,

special seals must be used. Contact Cascade.

➁

Flow less than recommended will result in reduced system

performance.

➂

Flow greater than maximum can result in excessive heating,

reduced system performance and short hydraulic system life.

Hoses and Fittings

Hoses and fittings for the CLAMP function should be at least

No. 6 with 9/32 in. (7 mm) minimum ID.
Hoses and fittings for the ROTATE function should be No. 8

with 13/32 in. (10 mm) minimum ID.

5.1

Hydraulics

Содержание 14J Series



























































Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды

cascade corporation 14J Series, Руководство по обслуживанию

Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды