cascade corporation 14J Series Скачать руководство пользователя страница 28

Страница: 28 / 58

6921413

SERVICE

RC2118.eps

RC2648.eps

RC2125.eps

RC0178.eps

RR0550.eps

4.4-3

Drive Group Reassembly

Build up the pinion/worm gear assembly vertically with the

pinion gear down.

Pinion with seal and non-sealed bearing –

Position

the seal against the pinion gear, spring-side facing

housing. Apply Loctite 271 (red) to the bearing seating

area, as shown. Press a non-sealed housing bearing

onto the pinion shaft.

NOTE:

If installing a sealed bearing with external seal,

pry out bearing seals and then press into pinion shaft.

Remove excess Loctite.

Pinion with sealed bearing –

No external seal is used.

Apply Loctite 271 (red) to the bearing seating area as

shown. Press housing bearing onto the pinion shaft.

Remove excess Loctite.

CAUTION:

Make sure Loctite does not squeeze into the

seal or bearings.

Preheat worm gear to 93 °C (200 °F). Install the key,

worm gear, cover plate pinion bearing and snap ring on

the pinion.

Apply Loctite 271 (red) to the housing seating area

and shoulder for the housing pinion bearing. Install the

complete pinion assembly into the housing. Remove

excess Loctite.

CAUTION:

Make sure Loctite does not squeeze into the

seal or bearings.

Install the worm's outer bearing race in the drive motor

side of the housing. Make sure the race taper is inward,

as shown.

Install the drive motor as described in Section 4.6-1.

Install the worm and bearings into the housing. Fully

engage the worm with the drive motor shaft. Install the

remaining outer bearing race. Make sure the race taper

is inward as shown.

PINION WITH SEAL AND NON-SEALED BEARING

PINION WITH SEALED BEARING

Pinon

Gear

Seal

Seating

Area

Bearing

Seating

Area

External

Seal

Housing

Pinion

Bearing

Housing

Pinion

Bearing

(Sealed)

Housing

Worm Gear,

Bearing, Snap Ring

Key

Содержание 14J Series



























































Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды

cascade corporation 14J Series, Руководство по обслуживанию

Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды