cascade corporation 14J Series Скачать руководство пользователя страница 50

Страница: 50 / 58

6921413

SERVICE

Attach two eyebolts to the baseplate. Attach an overhead

hoist and take up the slack in the chains.

Baseplate Capscrews −

Remove the capscrews

fastening the baseplate to the bearing assembly. Lift the

baseplate away. For reassembly, tighten the capscrews

using the following technique:

Clean and dry capscrews. Apply Loctite 242 (Blue) to

capscrew threads and threaded holes in the faceplate.

Threads must be clean and dry for new Loctite to cure

properly.

Tighten using the alternating cross pattern shown to

one-half the final torque value shown below.

Tighten using the alternating cross pattern to the final

torque value, then double-torque by backing off one-half

turn and immediately retightening to a final torque of:

14J –

38 ft.-lbs. (52 Nm)

18J –

66 ft.-lbs. (90 Nm)

CAUTION:

Do not reuse the old capscrews. Use new

capscrews and lockwashers (if equipped) when installing a

new bearing assembly.

CL3010.eps

CL2983.eps

Seal

Baseplate

Capscrews

Eyebolts

Cross Pattern

Tightening

Sequence

Cross Pattern

Tightening

Sequence

Back (driver's) Views

28G (Early Models), 36G-140G Models

Back (driver's) Views

28G (Current Models)

RC3688.eps

Bearing

Assembly

Baseplate

WARNING

: Verify that the overhead hoist

and chains or straps are rated for the weight

of the attachment. Refer to nameplate for

attachment weight.

4.10-2

Bearing Assembly Removal

and Installation

(Continued)

Drive

Pinion

Cover

Faceplate

Содержание 14J Series



























































Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды

cascade corporation 14J Series, Руководство по обслуживанию

Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды