cascade corporation 14J Series Скачать руководство пользователя страница 6

Страница: 6 / 58

6921413

PERIODIC MAINTENANCE

RR1432.eps

RR1433.eps

CC0074.eps

2.3

2000-Hour Maintenance

After each 2000 hours of truck operation, in addition to the

1000-hour maintenance, perform the following procedures:
• Check

all

rotation bearing capscrews for proper

torque value. See Section 4.10-1 for inspection and

replacement procedures.

2.4

4000-Hour Maintenance

After each 4000 hours of truck operation, in addition to the

1000 and 2000-hour maintenance, perform the following

procedures:
• Due to normal mechanical wear and component service

life, cylinder seals should be replaced to maintain

performance and safe operation.

End Cover

Level Hole

Gear

Grease

Filling

(B)

Ball Race Grease

Fitting

(A)

Bearing

Wear tiles

Bearing

Stabilizer Capscrews

2.2

1000-Hour Maintenance

(Continued)

Every time the lift truck is serviced or every 1000 hours

of truck operation, whichever comes first, complete the

following maintenance procedures:
• Check rotator drive gearcase lubricant level.

Lubricant should be filled up to end cover level hole.

Add lubricant through the end cover hole.
If necessary, fill with Cascade Rotator Drive Lubricant,

Part No. 656300 or SAE 90 wt. gear lube (AGMA

'mild' 6 EP Gear Oil). Replace the plug.

• Inspect all load-bearing structural welds on arms

and cylinder anchors for visual cracks. Replace

components as required.

• Check edges of contact pads for wear or sharp nicks

that could damage or tear product being handled.

Grind edges smooth.

• Inspect frame bearings for wear. Replace if

necessary.

• Inspect wear tiles and contact pads for wear and

damage. Replace or repair, as needed.

• Tighten stabilizer hardware to 48 ft.-lbs. (66 Nm).

Cylinder

Anchor

Joint

End Cover

Hole (level

and fill hole)

Top Fill Hole

14J

18J

Содержание 14J Series



























































Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды

cascade corporation 14J Series, Руководство по обслуживанию

Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды