cascade corporation 14J Series Скачать руководство пользователя страница 39

Страница: 39 / 58

6921413

SERVICE

CCW

RR1486.eps

RR1487.eps

RR1488.eps

ccw

RR0524.eps

4.7

Drive Control Valve

4.7-1

Drive Control Valve Service

Rotator Drive

Control Valve

Plug

Fittings

WARNING

: Before removing any hoses,

relieve pressure in the hydraulic system.

With the truck off, open the truck auxiliary

control valve(s) several times in both

directions.

Disconnect the hydraulic hoses and tubes (if equipped)

to the drive control valve. Tag hoses and tubes for

reassembly.

Remove the capscrews fastening the valve to the

baseplate (14J) or drive group (18J). For 18J

attachments, keep track of the two O-rings between

the valve and drive motor. For reassembly, tighten the

capscrews to the following torque value:

14J –

70 in.-lbs. (8 Nm)

18J –

16 ft.-lbs. (22 Nm)

Remove cartridges and fittings from the valve.

Remove the O-rings and back-up rings from the

cartridges.

Clean all parts with clean solvent. Remove any burrs or

sharp edges with emery cloth.

For reassembly, reverse the above procedures except

as follows:
• Install new O-rings and back-up rings on the

cartridges, as shown.

• Lubricate the cartridges and seals with petroleum

jelly prior to reassembly.

Rotator Drive

Control Valve

O-Rings

Tubes

Valve

Hoses

Body

Counterbalance

Cartridges

Counterbalance

Cartridges

Back-up Rings

O-Rings

Counterbalance

Cartridge

GA0486.eps

14J Attachments

18J Attachments

Valve

Содержание 14J Series



























































Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды

cascade corporation 14J Series, Руководство по обслуживанию

Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды