cascade corporation 14J Series Скачать руководство пользователя страница 44

Страница: 44 / 58

6921413

SERVICE

WARNING

: Before removing hydraulic

lines or components, relieve pressure in the

hydraulic system. With the truck off and

move the truck auxiliary control valve(s)

several times in both directions.

4.8-3

Relief Valve Adjustment

(CLAMP Circuit)

IMPORTANT:

Check the attachment nameplate for

hydraulic pressure settings.

Clamp Relief Adjustment

Confirm that the TRUCK pressure delivered to the

attachment revolving connection is within the range

shown on the attachment nameplate:

Recommended –

2250 psi (155 bar)

Maximum –

2755 psi (190 bar)

Install a 5000 psi (345 bar) pressure gauge to the valve

body TEST port (No. 4 O-ring fitting required).

NOTE:

Some valve bodies have two test ports. Install

the pressure gauge in either one.

Fully open arms. Clamp a rigid load or Clamp Force

Indicator at normal speed. Release control lever and

note pressure gauge reading.

Adjust the attachment relief cartridge on the end block

to show a maximum setting of 2250 psi (155 bar).

Turn clockwise (CW) to increase pressure,

counterclockwise (CCW) to decrease pressure. Tighten

jam nut.

Repeat Steps 3 and 4 to confirm setting.

REVOLVING CONNECTION

SSL

SSR

CL2

OP2

OPCK

CLC

OPCK

CL1

OP1

CC0352.eps

End Block

Body

TP, Test Port

CLAMP Check

Cartridge

OPCK1, Cylinder

OPEN Check

Cartridge

OPCK2, Cylinder

OPEN Check

Cartridge

Flow Divider

Cartridge

CLAMP Circuit

Supply Hoses

CLAMP Circuit

Supply Hoses

Front View

(Revolving Connection with Sideshift shown)

Side View

Содержание 14J Series



























































Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды

cascade corporation 14J Series, Руководство по обслуживанию

Результаты поиска

Содержание 14J Series

Отзывы:

Похожие инструкции для 14J Series

Бренды по названию

Популярные бренды