Canon Arizona 1300 Series Скачать руководство пользователя страница 118 | Manualshive

Страница: 118 / 248

background image

3.

Bend the height adjuster (small triangle in the top corner of the edge protector) slightly and then
straighten it again. This results in a slight bend (no more than a media thickness), that allows the
media edge to move more freely under the protector.

[48] Media Edge Protector Height Adjuster

IMPORTANT

If the height adjuster area is higher than 1 mm from the platen, there is a possibility that
the carriage may hit the edge of the protector and thus damage printhead nozzles.

4.

Peel the backing layer from the double-sided tape on the back of the protector.

5.

Place the bent edge of the protector into the media cut guide, but do not press down on the tape
yet.

6.

Slide the protector towards the media edge until the inside edge of the height adjuster is
positioned over the media edge (see figure below).

NOTE

Do not let the plastic edge near the arc butt up against the media edge or the device may
not let the media pass smoothly.
The vacuum in the platen will hold the main part of the protector in place while the image
is printed.

Media Edge Protectors

118

Chapter 7 - Roll Media Option

«
...
116
117
118
119
120
...
»

Содержание Arizona 1300 Series

























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Arizona 1300 Series

Pixma MG2400 Series

Бренд: Canon Страницы: 2

Бренд: QMS Страницы: 27

Бренд: QMS Страницы: 3

DocuPrint C3055 DX

Бренд: Xerox Страницы: 20

Бренд: OKIDATA Страницы: 182

WorkCentre PE120i

Бренд: Xerox Страницы: 8

Бренд: Sindoh Страницы: 33

Бренд: Hitt Marking Devices Страницы: 27

WorkCentre WC7530

Бренд: Xerox Страницы: 280

Бренд: Z Corporation Страницы: 70

Бренд: Epson Страницы: 59

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 4

Бренд: Epson Страницы: 86

Бренд: Epson Страницы: 104

Бренд: Epson Страницы: 76

Бренд: Epson Страницы: 133

Бренд: Epson Страницы: 145

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды