manualshive.com logo in svg

Canon Arizona 1300 Series, Руководство пользователя

Профессиональные печатные системы Canon Arizona серии 1300 - это надежные и мощные устройства для вашего бизнеса. У вас есть возможность скачать бесплатно руководство пользователя на manualshive.com. Используйте ключевые слова "Руководство пользователя", "руководство", "скачать", "бесплатно" для получения всей необходимой информации о продукте.

Поделиться
Скачать
background image

Varnish Workflow Overview

Introduction

Arizona printers with the Varnish Option can overprint varnish on top of a printed image in
selected areas in a print job or as a flood coat. The printing of varnish applies only to flatbed
printing and is not available with the RMO.

NOTE

The Varnish option is not available for print jobs that use the High Definition print mode. Varnish

can be used with all other print modes.

Printing varnish creates a high value-added special effect. However, since this is an additional
process after printing image data, it also decreases productivity. Due to the low productivity of
printing large areas of varnish, it is best to concentrate the use of this feature on spot decoration.
Fortunately, the Arizona printer "blank space" skipping feature skips over areas in the print that do
not contain varnish, and greatly improves the net productivity of spot applications.

Varnish is printed as a second process after the CMYK(W) image is printed. Immediately after
printing a CMYK(W) image. The gantry moves to the start of image position and prints a varnish
spot or printer generated flood data using three additional passes.

NOTE

Varnish is actually "clear ink" and is for decorative purposes only. It does not provide additional

protection to the printed image.

Spot Versus Printer Flood Fill

Varnish data can be applied to a print job in two ways: Printer Flood Fill or Spot Data.
• A Printer Flood Fill is like an auto-fill that is done by the printer, where varnish data fills the

entire bounding box (the rectangular area that defines the total perimeter) of the image.

• Varnish Spot data can be defined in image editing applications such as Adobe Illustrator® or

with the Spot Layer tool in the ONYX workflow.

The Spot Data can be defined as either Spot 1 or Spot 2. The same spot data can be used to print
either varnish or white ink, or both.

Varnish Workflow Data Preparation

Varnish print job output can be accomplished in a variety of ways depending on the desired
results and preferred working process. There are three primary methods. The workflow options
are:
• Printer flood fill configuration,
• ONYX software Spot Layer Tool, and
• Varnish spot data image preparation.

Printer Flood Fill Configuration

 in the ONYX workflow does not require any pre-rip file

preparation and is the easiest method of achieving varnish output. All that is required is to
configure ONYX to use a Varnish Flood. The printer flood encompasses the bounding box (the
outer border of the image) of the file being processed.

ONYX Software Spot Layer Tool

 offers many options to process an image, and thus allows

various possible configuration choices. You can save these configurations as Filters and place
them in a Quick Set and this makes it possible to re-create with minimal effort settings that are
often used. All work with the Spot Layer tool requires an ONYX media profile with at least one
spot colour.

Varnish Workflow Overview

130

Chapter 9 - Manage a White Ink Workflow

Содержание Arizona 1300 Series

























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Arizona 1300 Series

Magicard Prima Brochure preview
Prima
Бренд: Magicard Страницы: 6
GBC AdvancedPunch Pro Operation & Instruction Manual preview
AdvancedPunch Pro
Бренд: GBC Страницы: 92
TE Connectivity T3212 Quick Start Manual preview
T3212
Бренд: TE Connectivity Страницы: 2
TE Connectivity T3200 Replacement Instructions preview
T3200
Бренд: TE Connectivity Страницы: 2
Savin C2410 Reference Manual preview
C2410
Бренд: Savin Страницы: 160
Ultra electronics MAGICARD 300plus Quick Start Manual preview
MAGICARD 300plus
Бренд: Ultra electronics Страницы: 45
Radio Shack TRS-80 MICRO Hardware Manual preview
TRS-80 MICRO
Бренд: Radio Shack Страницы: 42
Evolis Zenius User Manual preview
Zenius
Бренд: Evolis Страницы: 63
Lexmark XS790 Series Brochure & Specs preview
XS790 Series
Бренд: Lexmark Страницы: 8
SEH SEH InterCon PS54a-G Hardware Installation Manual preview
SEH InterCon PS54a-G
Бренд: SEH Страницы: 24
VORON STEALTHBURNER Manual preview
STEALTHBURNER
Бренд: VORON Страницы: 73
Xerox WorkCentre Pro 416 User Manual preview
WorkCentre Pro 416
Бренд: Xerox Страницы: 470
oti OCT Service Manual preview
OCT
Бренд: oti Страницы: 33
SINTERIT SIEVE User Manual preview
SIEVE
Бренд: SINTERIT Страницы: 16
Oce Finisher AF1 User Manual preview
Finisher AF1
Бренд: Oce Страницы: 61
VOLUMIC STREAM MK3 Series User Manual preview
STREAM MK3 Series
Бренд: VOLUMIC Страницы: 70
Triumph Adler DC 2025 Instruction Handbook Manual preview
DC 2025
Бренд: Triumph Adler Страницы: 139
PICASO 3D Designer XL PRO User Manual preview
Designer XL PRO
Бренд: PICASO 3D Страницы: 72

Бренды по названию

Популярные бренды

Загрузить еще бренды