Canon Arizona 1300 Series Скачать руководство пользователя страница 184

Страница: 184 / 248

Recover Nozzles by Swabbing

Introduction

If a nozzle or group of nozzles do not recover from standard AMS practices, it may be necessary
to recover the nozzle by swabbing.

Equipment

• Foam Tipped Swab (3010118211)
• Flush (3010106646 Flush UV 1 Litre) or Isopropyl alcohol (99% pure)

NOTE

Tip:

To help locate nozzles that need recovering remove the nozzle check print from the vacuum

table and place it on the floor under the carriage in the maintenance area. Make sure it is in the

correct orientation so the colours are aligned. The print represents a projection of the jetting

performance of each printhead. This makes it easier to trace a nozzle or group of nozzle outs

back to the area on the actual printhead nozzle plate that requires swabbing.

Procedure

Slide open the maintenance station drawer.

Push the Raise Carriage button.

Dip the foam end of the swab in a small container of flush solution.

Use the lip of the container to wipe away any excess flush from the swab.

IMPORTANT

Keep swabs clean prior to use. Do not dip a used swab in the flush solution.

Do not let the seam on the foam contact the bottom of the printhead. This can damage the
printhead. See the next figure.

Recover Nozzles by Swabbing

184

Chapter 11 - Maintenance

Содержание Arizona 1300 Series

























































































































































































































































Результаты поиска

Содержание Arizona 1300 Series

Отзывы:

Похожие инструкции для Arizona 1300 Series

Бренды по названию

Популярные бренды

Canon Arizona 1300 Series, Руководство пользователя

Результаты поиска

Содержание Arizona 1300 Series

Отзывы:

Похожие инструкции для Arizona 1300 Series

Бренды по названию

Популярные бренды