Canon Arizona 1300 Series Скачать руководство пользователя страница 210 | Manualshive

Страница: 210 / 248

background image

Change Ink Filter

Introduction

Each ink colour has a filter that removes any particulate matter from the ink as it is pumped from
the ink bag to the printheads. The ink filters are located in an enclosure below the ink bays with
each filter positioned below its ink bag.

When to do

An ink filter must be replaced after 50 litres of ink have been consumed or the effects of a clogged
filter appear. If the Nozzle Check print shows one colour weaker than normal, this is an indication
that the ink filter for the affected colour is clogged and the filter must be replaced. If an ink filter
becomes clogged, it will trap colour pigment and affect the colour strength of printed images. If
you notice that an ink reservoir takes a long time to fill, check the Maintenance tab in the user
interface for when the filter for that colour of ink was last changed; it may be time to replace it.
Make sure that the ink tubing from that filter is not kinked. It is important to change the filter on
schedule and before these symptoms occur; damage to the ink system may result.

NOTE

Ink filters contain air that must be released. If you don't bleed the filters you will see poor image
quality. Air in the ink filter can affect the vacuum and result in dripping ink and deteriorated
image quality as a result of nozzle dropout. Failure to bleed the ink filters can lead to an overflow
of ink that will result in ink dripping from the carriage and you may need to place a service call.
You will be notified by the printer Maintenance tab when it is necessary to change or bleed a
filter.

CAUTION

Wear gloves when contact with ink or maintenance materials is possible. Gloves should always
overlap sleeves. Follow the ink related Safety Data Sheets (SDS) guidelines carefully in order to
ensure maximum safety. For example use Ansell Microflex 93-260 gloves, which offer a
protection against UV inks and flush up to one hour. Pollution with other chemicals can shorten
the protection time against UV inks and flush.
Wear eye protection as prescribed in this document when performing a task or action in this
area.

Procedure

1.

Disengage the ink bag for the ink colour filter you will replace. To do this press the release tab on
the left side of the quick-release ink bag coupler and then pull it out to disconnect the ink bag.
Use the colour codes on the ink filter enclosure door to identify the correct ink bag and filter.

Change Ink Filter

210

Chapter 11 - Maintenance

«
...
208
209
210
211
212
...
»

Содержание Arizona 1300 Series

























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Arizona 1300 Series

Бренд: QMS Страницы: 160

Бренд: QMS Страницы: 110

Бренд: QMS Страницы: 158

Бренд: CAB Страницы: 144

Power Defense PD3

Бренд: Eaton Страницы: 4

imagePROGRAF GP-540

Бренд: Canon Страницы: 82

Бренд: Xerox Страницы: 44

Бренд: Oki Страницы: 76

imageRUNNER 2545i

Бренд: Canon Страницы: 37

Бренд: Lexmark Страницы: 2

Бренд: Oce Страницы: 306

Бренд: Printek Страницы: 31

Бренд: Ricoh Страницы: 152

Бренд: iFactory3D Страницы: 14

Бренд: Muratec Страницы: 213

Бренд: Magicard Страницы: 108

Бренд: Epson Stylus Страницы: 4

Бренд: Oce Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды