Canon Arizona 1300 Series Скачать руководство пользователя страница 202 | Manualshive

Страница: 202 / 248

background image

Empty Ink Waste Trays

Introduction

There are two waste trays. The Purge Waste Tray is located under the Maintenance station. It
catches ink purged from either Manual maintenance or Automated printhead maintenance. The
Spit Waste Tray is located below the ink spit catcher. It accumulates waste ink from printhead
spitting.

[93] 1 = Purge Waste Tray 2 = Spit Waste Tray

When to do

Empty both waste trays weekly.

CAUTION

Wear gloves when contact with ink or maintenance materials is possible. Gloves should always
overlap sleeves. Follow the ink related Safety Data Sheets (SDS) guidelines carefully in order to
ensure maximum safety. For example use Ansell Microflex 93-260 gloves, which offer a
protection against UV inks and flush up to one hour. Pollution with other chemicals can shorten
the protection time against UV inks and flush.
Wear eye protection as prescribed in this document when performing a task or action in this
area.

CAUTION

UV inks and flush liquids can be harmful if not properly handled. Follow always the Safety Data
Sheets (SDS) guidelines carefully in order to ensure maximum safety.

NOTE

Although the carriage is oriented so that the nozzles spit into the slots in the spit catcher, some
ink will find its way onto the flat surfaces. Open the maintenance drawer to check the surface of
the spit catcher daily. If you see any ink wipe it up with a clean cloth or paper towel.

Equipment

• Foam Tipped Swab or Cloth-Poly Wipe

Empty Ink Waste Trays

202

Chapter 11 - Maintenance

«
...
200
201
202
203
204
...
»

Содержание Arizona 1300 Series

























































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Arizona 1300 Series

Бренд: Oki Страницы: 282

Бренд: MakerPi Страницы: 21

Бренд: Xerox Страницы: 48

Бренд: Oce Страницы: 4

Бренд: Oki Страницы: 40

Бренд: Oki Страницы: 104

Бренд: Oki Страницы: 28

Бренд: Oki Страницы: 23

Бренд: Oki Страницы: 108

Бренд: Oki Страницы: 2

Бренд: Oki Страницы: 94

Бренд: Oki Страницы: 135

Бренд: Oki Страницы: 97

Бренд: Oki Страницы: 280

Бренд: Oki Страницы: 123

Pacemark PM4410

Бренд: Oki Страницы: 144

Pacemark PM4410

Бренд: Oki Страницы: 28

Бренд: Oki Страницы: 176

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды