Cafection TOTAL LITE Скачать руководство пользователя страница 69

Страница: 69 / 72

TOTAL LITE Revision 1

SERVICE MANUAL FOR INNOVATION

TOTAL LITE

Single-Cup Brewer

11.2 Error message list (continued)

Low water level in tank.

The water tank tank failed to fill to maximum within the required time. The water inlet valve is de-

activated as a safety.

Maximum filling time is 4 minutes when you power ON the coffee brewer.

Maximum filling time is 1 minute after the first tank fill.

Check water supply line for proper pressure. If you are using a waterline filter, it might be worn out and

needs to be replaced.

Press button on screen to restart the tank filling process.

Water tank not full. Please wait while filling. 1 to 3 minutes.

This message will be on screen after powering ON the coffee brewer until water tank gets full.

Water temperature not high enough.

The TOTAL LITE will stop dispensing drinks if actual water temperature is below the ‘Warming up’

temperature in the service menu, ‘system’ tab. To disable this feature set the warming up temperature

to 0.

Troubleshooting

Содержание TOTAL LITE









































































Результаты поиска

Содержание TOTAL LITE

Отзывы:

Похожие инструкции для TOTAL LITE

Бренды по названию

Популярные бренды

Cafection TOTAL LITE, Руководство по обслуживанию и установке

Результаты поиска

Содержание TOTAL LITE

Отзывы:

Похожие инструкции для TOTAL LITE

Бренды по названию

Популярные бренды