background image

TOTAL LITE Revision 1

SERVICE MANUAL FOR INNOVATION

 

TOTAL LITE

 

 

Single-Cup Brewer

 

53

Cleaning & Sanitizing

8.7.2   Soluble Canisters

Removing whipping assembly for cleaning

Frequency: Weekly or every 200 cycles

If there is residue, remove the assembly for manual cleaning under hot water:

1. Remove the tube from the base;

2. Lift off the funnel and twist off the whipper chamber, remove propeller,    

 

whipper 

base and clean all parts and gaskets with hot water;

3. Rinse thoroughly under hot water and use tube brush if necessary for    

 

tubing area;

4. Air dry completely;

5. Reinstall all parts in the reverse order.

6. Order a large beverage to confirm that all parts or switches have been 

  replaced.

Removing canisters for cleaning

Frequency: Monthly or every 1,000 cycles

To ensure a consistent product quality, we recommend removing and 

emptying the canisters on a monthly basis. This will ensure that the 

product does not adhere to the walls of the canister.

1.   Unlock the door;

2.   Remove the top cap of the machine;

3.   Pull the canister up through the top of the brewer to disengage it from the  

    motor and transmission; 

4.   Clean and sanitize under hot water and air dry completely;

5.   Reinstall all parts and reload products in the reverse order.

6.   Order a beverage to confirm that all parts or switches have been replaced.

Содержание TOTAL LITE









































































Отзывы: