background image

TOTAL LITE Revision 1

SERVICE MANUAL FOR INNOVATION

 

TOTAL LITE

 

 

Single-Cup Brewer

 

51

8.6.2  Emptying the waste bin

Frequency: Daily or every 200 cycles

After each coffee cycle, the spent grounds and used filter paper are automatically discarded into the 

waste bin located in the stand. To prevent the bin from overflowing there is an automatic function which 

stops the brewer and shows the following message on the screen:

The maximum setting =   2000

The minimum setting =   0

Setting the maximum counter to 0  will disable the automatic function and will cause an overflow 

problem if the bin is full.

The equipment will not dispense coffee beverages until the bin is emptied and the counter is reset. To 

reset the counter see section 6.2. This factory set counter can be adjusted to the waste bin size used. 

See the machine parameters for more instructions on changing the setting.

How to empty the stand waste bin:

1. Open the stand door located directly below the brewer;

2. Cut the filter paper 4 “ below the drum with scissors or tear gently; DO NOT YANK ON THE PAPER!

3. Remove the filled plastic bag from the spent grounds bin and replace with a new one;

4. See section 7.11 to see how to put the paper back in place.

How to empty the brewer waste bin:

1. Open the brewer door;

2. Take the front panel off;

3. Cut the filter paper 4” below the drum with scissors or tear gently; DO NOT YANK ON PAPER!

4. See section 7.11 to see how to put the paper back in place;

5. Replace the front panel and close the door.

It is very important not to yank on the filter paper. Doing so may prevent the brewer from functioning 

properly.

* If you are using the internal waste bin provided with the unit, we recommend to set the counter to 25 

cycles.

Cleaning & Sanitizing

Содержание TOTAL LITE









































































Отзывы: