Cafection TOTAL LITE Скачать руководство пользователя страница 19

Страница: 19 / 72

TOTAL LITE Revision 1

SERVICE MANUAL FOR INNOVATION

TOTAL LITE

Single-Cup Brewer

5.2

Removing the compact flash card

To remove the compact flash card pull it towards you.

5.3

Inserting the compact flash card

To insert the compact flash card make sure it’s aligned correctly with the receptacle and push it. It may

required a LITTLE amount of force but do not push it too hard.

WARNING! If the compact flash card is not inserted the right way, it’s upper corner will not enter the

receptacle. If it happens DO NOT PUSH ANYMORE or damage could be done. Flip the card and push

it back in.

5.4

Compact flash card version

At start-up, the screen will indicate the GUI (compact flash card) version #, see picture below;

Compact flash card

(Location in newest machines)

White side

Compact Flash Card

Compact flash card

(Location in older machines)
Colored side

Содержание TOTAL LITE









































































Результаты поиска

Содержание TOTAL LITE

Отзывы:

Похожие инструкции для TOTAL LITE

Бренды по названию

Популярные бренды

Cafection TOTAL LITE, Руководство по обслуживанию и установке

Результаты поиска

Содержание TOTAL LITE

Отзывы:

Похожие инструкции для TOTAL LITE

Бренды по названию

Популярные бренды