Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Скачать руководство пользователя | Manualshive

Страница: 347 / 364

background image

Operation

Product manual 2CKA001473B5342

│

347

12.7.6 System settings - User settings

The panel language and the function of sensors and door communication can be set within the
user settings. The user settings can also be reset.

Language

The language of the panel and the separators to be used can be specified via the "Language"
tab. Here a selection can be made from the specified options within the drop-down menu.

■

Language

Options:

<Language>

The parameter is used to specify the language of the panel.

■

Separator

Options:

<Decimal separator>

<Thousands separator>

The parameter is used to specify the type of the decimal (comma or full stop) and thousands
separator (comma or full stop).

Sensors

The "Sensors" tab can be used to specify how strong the haptic feedback of the panel is to be
when it is touched.

■

Activate haptic feedback

Options:

Activate

Deactivate

This parameter is use to activate or activate the haptic feedback. Then the vibration can be
adjusted with the slider (left = weak, right = strong).

■

Temperature

Options:

<Temperature>

<Wall type>

The parameter is used to specify the temperature unit. Also the type of wall can be specified,
since this has an effect on the temperature reading. The temperature is indicated in the status
display on the dashboard by activating the "Show temperature in the status display" checkbox.

«
...
345
346
347
348
349
...
»

Содержание Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Busch-SmartTouch ST/A10.11-811

Бренд: GE Страницы: 148

Бренд: FabiaTech Страницы: 3

Бренд: FabiaTech Страницы: 3

Бренд: Samsung Страницы: 2

Бренд: C&T Solution Страницы: 60

SOLARCRUISE Series

Бренд: XUNZEL Страницы: 12

Бренд: Tsun Страницы: 2

Бренд: Tesla Страницы: 20

Бренд: Aaeon Страницы: 41

Бренд: Iddero Страницы: 40

Бренд: AXIOMTEK Страницы: 62

Бренд: Ariston Thermo Страницы: 36

Бренд: Philips Страницы: 34

Бренд: Philips Страницы: 36

Бренд: Philips Страницы: 67

Бренд: Philips Страницы: 84

Бренд: Sunforce Страницы: 2

Solar 12 Volt Battery Maintainer

Бренд: Sunforce Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды