Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Скачать руководство пользователя | Manualshive

Страница: 248 / 364

background image

KNX control elements and application parameters

Application "Internal RTC"

Product manual 2CKA001473B5342

│

248

configuration.

Note

This parameter is only available when "Control value type" parameter is set
either on "PI continuous, 0 – 100%", "PI PWM, On/Off“ or "Fan coil".

10.24.50 Control of additional cooling stage — P-component

Options:

Setting option between 1 - 25

The P-component stands for the proportional range in a control. It fluctuates around the setpoint
value and can be used to influence control speed of a PI controller. The smaller the value set,
the faster the control reacts. However, the value should not be set too small because otherwise
there may be a risk of an overshoot. A P-component from 1 to 25 K can be set.

Notice

This parameter is only available when "Control value type" parameter is set
either on "PI continuous, 0 – 100%", "PI PWM, On/Off“ or "Fan coil". In addition,
the "Cooling type" parameter must be set on "Free configuration".

10.24.51 Control of additional cooling stage — I-component

Options:

Setting option between 0 - 600

The I-component refers to the readjust time of a control. The integral component has the effect
of moving the room temperature slowly toward, and ultimately reaching, the setpoint value.
Depending on the type of system used, the reset time has to have different values. In general,
the more inactive the overall system, the greater the readjust time.

Notice

This parameter is only available when "Control value type" parameter is set
either on "PI continuous, 0 – 100%", "PI PWM, On/Off“ or "Fan coil". In addition,
the "Cooling type" parameter must be set on "Free configuration".

10.24.52 Control of additional cooling stage - Temperature difference to basic stage

Options:

Setting option between 0 - 25

The setpoint temperature of the additional stage is defined as a function of the current setpoint
temperature of the base stage and is expressed as a difference. The value represents the
setpoint value starting at which the additional stage will operate.

«
...
246
247
248
249
250
...
»

Содержание Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Busch-SmartTouch ST/A10.11-811

Бренд: Curtech Страницы: 4

Бренд: Vizio Страницы: 83

SIO-W221 Series

Бренд: C&T Страницы: 89

Бренд: IEI Technology Страницы: 112

Бренд: IEI Technology Страницы: 160

KS23 Trio Labstart

Бренд: Duomo Страницы: 4

Бренд: AXIOMTEK Страницы: 59

Бренд: AXIOMTEK Страницы: 68

Бренд: AXIOMTEK Страницы: 80

Бренд: Bongshin Страницы: 20

me2solar Aurora Pro

Бренд: Euro-Line Solar Страницы: 4

Бренд: Eelectron Страницы: 156

Бренд: CORAB Страницы: 6

Бренд: CORAB Страницы: 9

Power Panel C Series

Бренд: B&R Страницы: 93

Бренд: Planar Страницы: 53

Бренд: Van Der Valk Страницы: 28

Бренд: oventrop Страницы: 80

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды