Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Скачать руководство пользователя

Страница: 225 / 364

KNX control elements and application parameters

Application "Logical functions"

Product manual 2CKA001473B5342

│

225

Sending value when input 1 < input 2

Options:

Setting options from 0 - 255

The parameter is used to specify which output object is sent when input 1 is logically
smaller than input 2.

Telegram is sent at

Options:

Change output

Output 1 is larger than input 2

Output 1 is smaller than input 2

A telegram is sent when the selected condition is met.

Cyclic sending of output

Options:

Deactivated

Activated

The parameter is used to specify whether the output telegram is sent in cycles.
–

Deactivated

: No additional parameters available.

–

Activated

: The following parameter appears:

Cycle time

Options:

Setting options from 00:00:01 - 00:30:00

The parameter is used to specify the cycle time (hh:mm:ss).

–

Status converter

: This function is used to convert an input value into a 14-byte text or divide

it into several 1-bit telegrams. The following parameters are displayed:

Type of converter

Options:

1 bit -> text

1 byte -> text

1 byte -> 8x1 bit

2 byte -> 16x1 bit

See the explanation above.
– 1 bit -> text: A 1-bit value is converted into text. The following parameter appears:

Number of inputs

Options:

Setting options from 1 - 4

The parameter is used to set the number of available inputs. The following parameter
appears:

Using value xxxx

Options:

Deactivated

Activated

The parameter is used to specify whether the signal is used for the conversion into text.
–

Deactivated

: No additional parameters available.

–

Activated

: The following parameter appears:

Text for value xxxx

Содержание Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Результаты поиска

Содержание Busch-SmartTouch ST/A10.11-811

Отзывы:

Похожие инструкции для Busch-SmartTouch ST/A10.11-811

Бренды по названию

Популярные бренды

Busch-Jaeger Busch-SmartTouch ST/A10.11-811, Руководство по эксплуатации продукта

Результаты поиска

Содержание Busch-SmartTouch ST/A10.11-811

Отзывы:

Похожие инструкции для Busch-SmartTouch ST/A10.11-811

Бренды по названию

Популярные бренды