Busch-Jaeger Busch-SmartTouch ST/A10.11-811 Скачать руководство пользователя | Manualshive

Страница: 132 / 364

background image

KNX control elements and application parameters

Operation of "RGBW" control element“

Product manual 2CKA001473B5342

│

132

10.5.6 Type of colour/white lamp

Options:

RGB

HSV

RGB+W

RGB+Tunable White

Tunable White

The parameter is used to specify how the colour activation is to be controlled. Corresponding
sliders will be displayed in the control element. The type of colour control depends on the type
of lamp. Specific settings can be made for the lamps. For example, the colours can be changed
or the warm-white component can be adjusted.

RGB: Used for RGB lamp.
The following supplementary parameter is available:

■

Switching On/Off via:

Options:

Switch object

RGB feedback signal

The parameter is used to specify the On/Off control.

– Switch object: Setting, when the lamp contains a "Switch" object. The following

supplementary parameters are available:

■

Switched On -> preset value:

Options:

Deactivated

Activated

–

Deactivated

: No presets are sent when the lamp is switched on.

–

Activated

: The stored presets are sent when the lamp is switched on.

■

Switched Off -> RGB value 0,0,0:

Options:

Deactivated

Activated

–

Deactivated

: No RGB values are sent when the lamp is switched off.

–

Activated

: The RGB values (0,0,0) are sent when the lamp is switched off. This parameter is

important for lamps that do not contain a "Switch" object.
–

RGB feedback

: Setting when the lamp contains no "Switch" object but is switched off via

the RGB values.

«
...
130
131
132
133
134
...
»

Содержание Busch-SmartTouch ST/A10.11-811













































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Busch-SmartTouch ST/A10.11-811

Бренд: Samsung Страницы: 587

Бренд: Avalue Technology Страницы: 100

Isys i/O TPMC-15-CH

Бренд: Crestron Страницы: 58

Бренд: Wolf Страницы: 2

Бренд: King Pigeon Страницы: 2

28PW6517 - annexe 1

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 1

Бренд: Philips Страницы: 2

Бренд: Philips Страницы: 20

Бренд: Philips Страницы: 28

Бренд: Philips Страницы: 144

Бренд: Sunforce Страницы: 4

Бренд: Panasonic Страницы: 8

BL C131A - Network Camera - Pan

Бренд: Panasonic Страницы: 4

BB-HCM581A - Network Camera Pan

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 26

Бренд: Panasonic Страницы: 25

Бренд: Panasonic Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды