Bosch MSI 60 Скачать руководство пользователя страница 91

Страница: 91 / 120

Online Measurement | 11

Bosch Motorsport

Modular Sensor Interface MSI 60

91 / 120

The automatically created sheet is inserted in the Project Tree under ‘Measurement Con-

tainer’ and ‘Device Channels’. If the MSI 60 is connected to RaceCon, live values of the

channels are shown.

a) Access to sheet
b) Raw and physical channel values
c) Characteristic values
d) Button for online offset calibration

11.2.2 Using the Measurement Sheets

When RaceCon is online, press the ‘F11’ key to switch from ‘Design Mode’ into ‘Race

Mode’.

The measurement sheet is extended to full screen.

The button for offset calibration is active.

Switch between different sheets using the tabs at the bottom of the page or the key-

board shortcuts associated with the sheets.

Press the ‘Esc’ key to return to ‘Design Mode’.

11.3 Online Calibration of Measurement Channels

– Analog sensors drift with age, temperature, etc.

– Manual calibration is necessary

– Solution: online offset calibration

– Example: acceleration sensor

Содержание MSI 60

























































































































Результаты поиска

Содержание MSI 60

Отзывы:

Бренды по названию

Популярные бренды

Bosch MSI 60, Руководство пользователя

Результаты поиска

Содержание MSI 60

Отзывы:

Бренды по названию

Популярные бренды