manualshive.com logo in svg

Bosch MSI 60, Руководство пользователя

Поделиться
Скачать
Bosch MSI 60 Скачать руководство пользователя страница 22

7 | Starting up

22 / 120

Modular Sensor Interface MSI 60

Bosch Motorsport

7 Starting up

The following chapter explains what you have to do before starting the MSI 60 and how

to connect it to RaceCon.

7.1 Before Starting

Install the software required for MSI 60 operation. It is developed for Windows 2000/XP/

Vista/7. Following software versions are used in this manual:

– MSI 60 setup, configuration and calibration: RaceCon V2.5 and following

– Measurement data analysis: WinDarab V7

Set up the 100 Mbit Ethernet connection to the MSI 60.

– All three Ethernet ports of MSI 60 are internally connected by a network switch.

– All Ethernet ports have ‘cable auto crossover’ functionality.

Minimum wiring loom of the Life connector (Red):

PIN

Description

1+2+3

12 V Supply Voltage

4+5

GND Supply Voltage

18

Ethernet Tx+

7

Ethernet Tx-

17

Ethernet Rx+

6

Ethernet Rx-

21

Ethernet Screen

7.1.1 Starting the MSI 60

The MSI 60 powers up by turning on the ignition of the car.

The ‘Link LED’ at the PC’s network adapter will illuminate. If the LED is off, check the wiring

harness.

7.1.2 About RaceCon

RaceCon is an all integrated software tool for configuration and calibration of Bosch Mo-

torsport hardware products. It is used to set up, configure and calibrate the MSI 60.

For better understanding, Bosch Motorsport offers a video tutorial that explains many

functions of RaceCon. The video tutorial is available in the ‘Software Download’ section on

www.bosch-motorsport.com.

7.1.3 Connecting the MSI 60 to RaceCon

The following screenshot shows an overview of the RaceCon main screen with its areas. All

(sub-) windows are resizable and dockable.

Содержание MSI 60

























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды