manualshive.com logo in svg

Bosch MSI 60, Руководство пользователя

Поделиться
Скачать
Bosch MSI 60 Скачать руководство пользователя страница 10

5 | Inputs and Outputs

10 / 120

Modular Sensor Interface MSI 60

Bosch Motorsport

5 Inputs and Outputs

The following chapter introduces the Input and Output Channels.

5.1 Input Channels

The MSI 60 provides diverse analog inputs which allows the direct connection of a multi-

plicity number of sensors.

5.1.1 Basic Analog Inputs

The MSI 60 basic analog inputs accept an input signal of 0 to 5 V. A 3.01 kOhm pull-up

resistor can be activated by software.

5.1.2 Differential Analog Inputs

The MSI 60 differential analog inputs offers a wide configurability. The inputs can be

switched between single ended or differential mode. In single ended mode input signals

of 0 to 5 V are accepted. In differential mode input signals are accepted in the range of -5

V to +5 V.

Three pull-up resistors can be activated by software. A 3.01 kOhm resistor can be used for

evaluation both ntc sensors and switches or push-buttons.

The resistors of 4.99 kOhm and 49.9 kOhm provide the direct connection of PT100 and

PT1000 sensors.

A selectable amplification of small input signals allows the direct connection of resistive

strain gauges.

For further wiring details please refer to the given figures.

Illustration 1: 

Differential sensor

Содержание MSI 60

























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды