Bosch MSI 60 Скачать руководство пользователя страница 79

Страница: 79 / 120

Analog and Frequency Inputs | 10

Bosch Motorsport

Modular Sensor Interface MSI 60

79 / 120

a) Channels available in computed sources.
b) Available measurements for channel.
c) Calculation of hysteresis channel.

10.5.1 Special Functionality: Vehicle speed

This functionality allows:

– High performance vehicle owners to measure wheel spin under acceleration and

wheel slip/lock under braking.

– Calculating vehicle ‘speed over ground’.

Vehicle speed calculation function

– Calculating vehicle speed of 2 wheel drive: (Wheel speeds of non-driven axle as in-

put).

Calculated speed is average of both speeds if speed difference between wheels

< limit.

Calculated speed is maximum of both speeds if speed difference between wheels

> limit.

– Calculating vehicle speed of 4 wheel drive: (Wheel speeds of all wheels as input).

Calculated speed is speed of 2nd fastest wheel.

10.5.2 Setting up calculated Speed

Click on tab ‘System Overview’.

Click on ‘Measurement Sources’ in the Toolbox.

Содержание MSI 60

























































































































Результаты поиска

Содержание MSI 60

Отзывы:

Бренды по названию

Популярные бренды

Bosch MSI 60, Руководство пользователя

Результаты поиска

Содержание MSI 60

Отзывы:

Бренды по названию

Популярные бренды