manualshive.com logo in svg

Bosch MSI 60, Руководство пользователя

Поделиться
Скачать
Bosch MSI 60 Скачать руководство пользователя страница 4

Content

iv / 120

Modular Sensor Interface MSI 60

Bosch Motorsport

12.3.2

Open Line Detection .................................................................................................................................................................

105

13 Firmware ..........................................................................................................................................................................

106

13.1 Firmware and Configuration.....................................................................................................................................................................

106

13.2 Firmware Update...........................................................................................................................................................................................

106

14 Clone the Unit .................................................................................................................................................................

109

15 GPS Sensor.......................................................................................................................................................................

111

15.1 GPS (Global Positioning System) ............................................................................................................................................................

111

15.2 Protocol ............................................................................................................................................................................................................

111

15.3 Sensor Recommendation ..........................................................................................................................................................................

111

15.4 Measurement Labels ...................................................................................................................................................................................

112

15.5 GPS Troubleshooting ..................................................................................................................................................................................

113

16 RaceCon Shortcuts..........................................................................................................................................................

114

17 Disposal............................................................................................................................................................................

115

18 Error Memory ..................................................................................................................................................................

116

18.1 General Note ..................................................................................................................................................................................................

116

18.2 Error Memory Representation in RaceCon .........................................................................................................................................

116

18.2.1

Accessing the Memory .............................................................................................................................................................

116

18.2.2

Cleaning the Error Memory ....................................................................................................................................................

116

18.3 Information on Errors available from the Error Memory...............................................................................................................

116

18.3.1

Error Memory Properties .........................................................................................................................................................

116

18.3.2

Error Properties ...........................................................................................................................................................................

116

18.4 Configuration .................................................................................................................................................................................................

116

18.4.1

Monitoring limits / Shortcut Detection / Cable Breakage..........................................................................................

116

18.4.2

Open Line Detection .................................................................................................................................................................

116

Содержание MSI 60

























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды