manualshive.com logo in svg

Bosch MSI 60, Руководство пользователя

Поделиться
Скачать
Bosch MSI 60 Скачать руководство пользователя страница 54

10 | Analog and Frequency Inputs

54 / 120

Modular Sensor Interface MSI 60

Bosch Motorsport

– Measurement labels with the characters ‘_fi’ show filtered values.

– The word ‘name’ in the table is a placeholder for the channel’s name.

Measurement label

Function

raw_name

mV value of sensor

raw_name_fi

filtered mV value of sensor

name

physical value of sensor

name_fi

filtered physical value

Filtered channels are routed through digital low pass filters:

– MSI 60 uses A/D converter oversampling and digital filtering to recording rate.

– Digital filters eliminate ‘out-of-band’ noise.

– Cut-off frequency automatically adjusted to recording rate.

– Linear phase – no signal distortion.

– Latency compensation – no filter delay in recorded data.

10.3 Configuring Inputs

This chapter describes how to configure the Input Sensors.

10.3.1 Configuring a predefined Bosch Sensor with the

‘Bosch Sensor Wizard’

1.

Click on ‘Measurement Sources’ in the Toolbox.

Содержание MSI 60

























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды